Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Align the holes and attach by using two sheet metal screws provided, shown in Fig. 1. Ceiling Radiation Damper - CRD 1. If fan is to be used in a fire resistive membrane ceiling, a ceiling radiation damper must be used. Otherwise proceede to Install the Fan. 2. If the ceiling radiation damper is already mounted to the fan from the factory, proceed to Install the Fan. 3. To mount the ceiling radiation damper to fan, make sure grille attachment tabs are facing down. Then place the inlet part of the fan into the ceiling radiation damper collar, and use self-tapping sheet metal screws #10x1/2 in. (by others) to screw through the damper collar and into the fan housing, shown in Fig. 2. If the fan/light combination is being used, make sure ceiling radiation damper has an electrical plug in it. The electrical plug must be inserted into the fan. Make sure the electrical wire will not interfere with damper operation, shown in Fig. 3. Wires from lighted grille Wires to ceiling fan Do not allow interference in this area Fig. 1 Fig. 3 Install the Fan 1. For best performance, choose a location with the shortest possible duct run and minimum number of elbows. Do not mount near cooking equipment, shown in Fig. 4. 2. Attach adjustable mounting brackets to fan, but leave the screws loose until proper height is determined, shown in Fig. 5. For fan and fan/light combination opening, cut a 141.8 by 113.4 inch hole in the ceiling. For fan/CRD combination opening, cut a 143.8 by 121.4 inch hole in the ceiling. For Frame Construction: Position unit between joists. Position brackets such that bottom edge of housing will be flush with finished ceiling, and tighten the adjustable mounting brackets, shown in Fig. 6. For Hanging Installations: Use Greenheck’s optional vibration isolator kit Part Number VI Kit. Using the fan’s standard adjustable mounting brackets and 10 by 32 threaded rod (by others) hang unit as shown in Fig. 7. Fig. 4 Do not install fan in this area 45. 45. Brackets can be arranged to adapt to most mounting conditions Fig. 5 Fig. 6 1. Adjust to be flush with finished ceiling Fan Ceiling 2. Tighten Fig. 7 ® WARNING ! To reduce the risk of fire, electric shock, or injury to persons, observe the following: • Suitable for use with solid-state speed controls. • Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. • Before servicing or cleaning unit, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. • Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. • Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities. • When cutting or drilling into wall or ceiling, do not damage electrical wiring or other hidden utilities. • Acceptable for use over a bathtub or shower when installed in a GFCI protected branch circuit. (Up through size SP-A390) • Never place a switch where it can be reached from a tub or shower. • Ducted fans must always be vented to the outdoors. • These fans are not recommended for cooking exhaust applications. They are designed primarily for low temperature, clean air applications only. The diagram shows the minimum distance these fans should be placed in relation to cooking equipment. • Fan/Light combination not to be installed in a ceiling thermally insulated to a value greater than R40. CAUTION ! • For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Attachment Tabs Fig. 2 GREENHECK P.O. BOX 410 SCHOFIELD, WISCONSIN 54476-0410 PH. 715-359-6171 ® SP/CSP models shown are UL and cUL listed E 33599 SP-B & CSP-B IOM FS Rev 8 March 2004 Copyright © 2004 Greenheck Fan Corp. Installation Recommendations Install the Fan - continued Wire the Fan Attach the Grille 3. Slide ductwork over the fan’s discharge collar and securely attach it with sheet metal screws. Make sure the screws do not interfere with damper operation. Check damper to make sure it opens freely. 1. If lighted grille is being used, plug wire into fan socket. If lighted grille and ceiling radiation damper are being used, plug wire from lighted grille into ceiling radiation damper socket. Do not plug wire directly into the fan socket. Make sure the wire does not interfere with the ceiling radiation damper operation. 2. Attach grille with two screws pro...