Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Zephyr
Dateigröße: 120.8 kb
Dateiname: ak088xas_liner_manual.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
For the liner installation, only the bottom of the custom hood is needed. Do not finalize the entire custom hood yet, because an opening is needed for the power pack. 0) c o (0 Û- Liner Model Power Pack Model Custom Hood Exterior Width *Inside Width (A) *Inside Depth (B) Without Backboard **With Backboard AK0800AS AK8000AS and AK8100AS 30 inches 28 1/2” 17 1/2” - 20 1/2” 17 1/8” - 20 1/8” AK0836AS 36 inches 34 1/2” AK0806AS AK8200AS 36 inches 34 1/2” 20 1/2” - 23 1/2” 20 1/8” - 23 1/8” AK0842AS 42 inches 40 1/2” AK0848AS AK8300ASX 48 inches 46 1/2” 20 1/2” - 23 1/2” 20 1/8” - 23 1/8” AK0854AS 54 inches 52 1/2” AK0860AS 60 inches 58 1/2” AK0886AS AK8800AG and AK8800AS 36 inches 34 1/2” 20 1/2” - 23 1/2” 20 1/8” - 23 1/8” AK0882AS 42 inches 40 1/2” AK0888AS 48 inches 46 1/2” AK0884AS 54 inches 52 1/2” AK0880AS 60 inches 58 1/2” *Dimension does not include 3/8” wide flange around liner. **The inside depth shown in the table above assumes a minimum cabinet backboard thickness of 3/8”. FIG 1: Zephyr recommends the base of the custom hood to be 3/4” thick plywood. The sides, front and backboard (if included) of the custom hood to be 3/4” thick, assuming standard cabinet widths. Consider the shape and size of the power pack to determine the configuration of the custom hood. For more details, refer to the installation manual of the power pack. Zephyr Corporation 2277 Harbor Bay Pkwy, Alameda, CA 94502 Tel: 1.888.880.8368 Fax: 1.888.990.8368 e-mail: productsupport@zephyronline.com 0) Installation - ESSENTIALS ZEPhtt AK08xxAS Adjustable Depth Liners CAUTION: Before installing, remove any protective film from all parts. The custom hood liner must be installed before the power pack unit. For installation into shallow cabinets (20-1/2” to 21-1/2“ inside depth) the power pack must be installed before the liner front panel section. This must be done because the power pack flange must fit under the liner front panel section when an overlap occurs. Refer to power pack instructions for mounting height details. hardware package, to each side of the main liner plate. (See figures 1 and 2) opening for the power pack. Remove the main liner plate (B) from the custom hood. the custom hood and secure it with (5) 3/4” screws. the external base of the custom hood (C). When inserting the main liner plate, push slightly on the pads (A) to prevent damage. Main liner plate should be positioned as far back as possible. custom hood. of the custom hood base. Take care not to scratch the main liner plate when installing the front panel section of the liner. Assemble it to the cabinet using (3) 1/2” screws. Note: When installing the power pack it will need to be secured to a wood surface and not only to the liner. See power pack installation manuals for more detailed mounting instructions. Installation - Power Pack Liner...