Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Wells
Dateigröße: 485.92 kb
Dateiname: ventlesshood.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
The technical content of this manual, including any wiring diagrams, schematics, parts breakdown illustrations and/or adjustment procedures, is intended for use by qualified technical personnel. Any procedure which requires the use of tools must be performed by a qualified technician. This manual is considered to be a permanent part of the appliance. This manual and all supplied instructions, diagrams, schematics, parts breakdown illustrations, notices and labels must remain with the appliance if it is sold or moved to another location. This appliance is made in the USA. Unless otherwise noted, this appliance has American sizes on all hardware. 4 INSTALLATION INSTALLATION UNPACKING & INSPECTION Carefully read all instructions in this manual before starting any installation. Carefully remove the hood from the carton. IMPORTANT: Appliance weighs 92 lbs (42.7 kg). Use appropriate care when removing from carton and installing on conveyor warmer. Remove all protective plastic film, packing materials and accessories from the hood before connecting electrical power or otherwise performing any installation procedure. Read and understand all labels and diagrams attached to the hood. Carefully account for all components and accessories before discarding packing materials. Store all accessories in a convenient place for later use. COMPONENTS: HIGH EFFICIENCY FILTER CHARCOAL FILTER COMPONENTS SHIPPED SEPARATELY CANOPY (2 ea) ADAPTER TOP NOTE: DO NOT discard the carton or other packing materials until you have inspected the hood for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. WARNING! Risk of Personal Injury Installation procedures must be performed by a qualified technician with full knowledge of all applicable electrical codes. Failure can result in personal injury and property damage. SETUP The conveyor-style warmer requires an adapter top (shipped separately) for mounting the hood. Place adapter top on warmer before setting hood in place. Carefully place hood on top of warmer. Orient hood so that power switch is on the same side as the power switch of the warmer. Center hood over the body of the warmer as shown in Fig. 2 below: CAUTION! Risk of Personal Injury and Property Damage Unplug conveyor warmer and allow to cool before beginning installation. IMPORTANT: Maintain required clearances of at least 6" between the appliance and adjacent combustible surfaces. Avoid storing flammable or combustible materials in, on or near the appliance. Fig. 2 Hood installation on warmer Check high efficiency filter and charcoal filter for proper installation. Charcoal filter slides into clips on the high efficiency filter. Airflow marks must point "up". Attach entry and exit canopies to pins on sides of hood. Canopies are interchangeable and may be mounted at either end. Maintain required clearances of at least 6" between the appliance and adjacent combustible surfaces. 5 ELECTRICAL INSTALLATION Refer to the nameplate. Verify the electrical power source. Voltage and phase must match the nameplate specifications. Plugging the hood into the wrong voltage can severely damage the unit . Your hood is equipped with a grounded electrical cord. This cord must be plugged into a properly grounded NEMA 5-15R (120V) or NEMA 6-15R (208/240V) single phase receptacle. Fig. 3 Electrical Plug and Receptacle Configuration WARNING! Electric Shock hazard All servicing requiring access to non-insulated electrical components must be performed by a factory authorized technician. DO NOT open any access panel which requires the use of tools. Failure to follow this warning can result in severe electrical shock. CAUTION! Electrical Shock Hazard The ground prong of the power cord is part of a system designed to protect you against electric shock in the event of internal damage. DO NOT cut the ground prong (large round prong) or twist a blade to make the plug fit an existing receptacle. IMPORTANT: Contact a licensed electrician to install and connect electrical power to the appliance. IMPORTANT: Damage due to being connected to the wrong voltage or phase is NOT covered by warranty. INSTALLATION (continued) 6 INSTALLATION (continued) 6 OPERATING CONTROLS Controls include a lighted POWER SWITCH and an amber REPLACE FILTER indicator light. Press POWER SWITCH to ON anytime conveyor warmer is operating. When power is first turned on, the REPLACE FILTER light will glow. As the fan comes up to speed and air flow is established, the REPLACE FILTER light will go out. If the REPLACE FILTER light does not go out, the filters must be replaced. However, the fan will continue to operate when the REPLACE FILTER light is lit. FILTER REMOVAL AND INSTALLATION Disconnect power from hood and conveyor warmer before servicing filters. Remove screw from filter access panel on front (operator's) side of hood. Slide filter pack (high efficiency filter and charcoal filter) from filter chamber. Sli...