Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
8. Use twist-on connectors and connect white wires together. 9. Tighten strain relief securely. 10. Replace terminal box cover. Tighten screw securely. 11. Reconnect power. Complete Installation 1. Connect vent system to hood liner. 2. Seal joints with duct tape. Check Operation A G D B A. Controls B. Light switch C. Blower switch D. Blower speed control switch 12 Move the light switch to the “1” position. The light should turn on. 22 Move the light switch to the “0” position. The light should turn off. 32 Move the blower switch to the “1” position. The blower should turn on. 42 Move the blower speed control switch to vary the blower speed from low (left) to high (right). 52 Move the blower switch to the “0” position. The blower should turn off. 62 If range hood does not operate, check that the circuit breaker has not been tripped or the house fuse blown. Disconnect power supply and check that the wiring is correct. 72 Reinstall filters. Place back edge of filter into channel at rear of hood liner and push filter up while pushing tab back. When filter is in place, release tab. Locking pin will hold filter in place. 82 Repeat for other filter(s). 92 Install hood enclosure. 9 RANGE HOOD USE Operation The canopy hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen. Hood control panel A G D B A. Controls B. Light switch C. Blower switch D. Blower speed control switch Operating the light 1. Move the light switch to the “1” position. The light should turn on. 2. Move the light switch to the “0” position. The light should turn off. Operating the blower 1. Move the blower switch to the “1” position. The blower should turn on. 2. Move the blower speed control switch to vary the blower speed from low (left) to high (right). 3. Move the blower switch to the “0” position. The blower should turn off. RANGE HOOD CARE Cleaning and Maintenance Be sure lights are cool before cleaning the hood. Exterior surfaces ¦ Do not use steel wool or soap-filled scouring pads. ¦ Rub in direction of the grain line to avoid marring the surface. ¦ Always wipe dry to avoid water marks. ¦ KitchenAid® Professional Formula Stainless Steel Cleaner & Polish is the cleaner recommended for cleaning stainless steel surfaces on this product. To order call our Customer Service Center at 1-800-442-9991 or order on-line at and ask for part number 8171420. To order from Canada, call 1-800-807-6777. ¦ If commercial cleaners are used, follow label directions. Do not use products that contain chlorine (bleach). Chlorine is a corrosive substance. For routine cleaning and fingerprints, use liquid detergent soap and water, or all-purpose cleaner. Wipe with damp cloth or sponge, then rinse with clean water and wipe dry. Filters The filters should be washed frequently. Place metal filters in dishwasher or hot detergent solution to clean. To remove filter: Use two hands to remove filter. Push tab back to release the locking pin, pull down and forward. Repeat with other filter(s). To reinstall filter: 1. Place back edge of filter into channel at rear of hood liner. 2. Push filter up while pushing tab back. 3. When filter is in place, release tab. Locking pin will hold filter in place. Repeat with other filter(s). Replacing a halogen lamp This hood liner uses 12-volt, 20 watt halogen lamps. Turn off the range hood and allow the halogen lamps to cool. Replace bulb using a tissue to handle bulb, or wearing cotton gloves. Do not touch bulb with bare fingers. 1. Disconnect power. 2. Remove 2 screws from the circular metal trim around the lamp assembly. 3. Pull the trim with the lamp assembly attached down far enough so that the lamp can be pushed out of the socket clips. 4. Insert the new lamp into the socket clips and push the lamp and trim assembly back up into the hood. 5. Replace the screws. 6. Reconnect power. Accessories Charcoal Filters (with grates) kit........Part Number 4396565 Replacement Charcoal Filters........Part Number 4378623 Two 6" (15.2 cm) round to 10" (25.4 cm) round vent transition kit ........Part Number 4396915 REQUESTING ASSISTANCE OR SERVICE If you need assistance or service in U.S.A2 Call the KitchenAid Customer eXperience Center toll-free at 1-800-422-1230. Our consultants are available to assist you. When calling: Please know the purchase date, and the complete model and serial number of your appliance This information will help us better respond to your request. Our consultants provide assistance with: ¦ Features and specifications on our full line of appliances ¦ Installation information ¦ Use and maintenance procedures ¦ Accessory and repair parts sales ¦ Specialized customer assistance (Spanish speaking, hearing impaired, limited vision, etc.) ¦ Referrals to local dealers, service companies, and repair parts distribut...