Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Before you begin: • Under no circumstances should this carrier be fitted to your car unless the exact settings specified in the enclosed vehicle application not be fitted to any vehicle not listed. If in any doubt ask in • Due to the construction of boot lids we recommend only two cycles cars with this carrier • Make sure all parts are included in the package. • Ensure that the vehicle boot lid/rear bumper are free from dirt and grime. REFER TO THE SEPARATE APPLICATION GUIDE TO DETERMINE THE CORRECT FITTING KIT. Kit Contents x2 x2 x2 x2 Made in the UK Halfords Ltd, Washford Redditch, B98 0DE PI480-01 3 5 1 2 REFER TO APPLICATION GUIDE Adjuster Plate 1 Position the assembled carrier on a clean surface as illustrated. (1) Release the 2 adjuster levers and (2) rotate the cycle support arms through 90. and lock in position. The quick release action should be firm for both opening and closing. The tension may be set by releasing the handles and turning clockwise. (3) Rotate the bottom feet 180. as shown. (1) Release the two carrier clamping levers and (2) turn the handles anti-clockwise until the angle adjusters are fully opened, (approx 40 turns). Rotate the large black angle adjusters upwards, ensuring a minimum of 45mm of screw is visible between the angle adjusters and the main carrier frame. Refer to the enclosed application list to find the correct angle for the vehicle support arm for your car. Insert the bolts from the outside faces in the specified holes A, B, C, D, E, F or G. Fit the thumb screw nuts to the inside face of the angle adjusters, making sure the bolt passes through the vehicle support arm. Refer to the enclosed application list to find the correct metal strap for your car. Refer to the enclosed application list to find the correct clamp bolt hole for your car. Insert the bolts, from the outer faces, through the metal clamps and the vehicle support arm. Fit the thumb screw nuts on the inside of the vehicle support arm. Refer to the enclosed application list to find the correct position for the extendible feet X, Y or Z. Insert the bolts from the outside faces, fit the thumb screw nuts to the inside of the carrier frame. 2 45mm INITIAL PREPARATION CARRIER SET-UP DO NOT PROCEED ANY FURTHER UNTIL STEPS 1 + 2 HAVE BEEN COMPLETED CORRECTLY DO NOT USE ANY HOLE SETTINGS OTHER THAN THOSE SPECIFIED FOR YOUR VEHICLE MAKE AND MODEL. 4 REFER TO APPLICATION GUIDE Strap Location 180° 1 2 3 REFER TO APPLICATION GUIDE Strap Selection REFER TO APPLICATION GUIDE Lower Mount Halfords hi 3 bike instructions 6/8/07 12:05 PM Page 3 6 9 10 7 3 (1) Before offering the carrier to your vehicle ensure the rear window/bodywork and rubber feet on the vehicle support arm are clean and free of dust. (2) For most vehicles it will be necessary to pre-bend the plain flat section of the metal straps. (3) Offer the carrier to the vehicle and hook the metal straps over the top edge of the tailgate of your vehicle. Ensure that the rubber protective sleeves are positioned to avoid any abrasion of the metal straps on the paintwork of the vehicle. Hook the feet under the bottom of your tailgate. In some cases it may be necessary to slightly open the tailgate to enable the feet to hook on. Ensure that both carrier clamping levers are in the closed position. Progressively tighten the levers on both sides of the carrier by turning them clockwise. When the resistance to turning starts to increase check the security of the carrier. Continue gradually tightening both levers until the carrier is firmly fixed in all directions. SLIGHTLY ABOVE HORIZONTAL 11 12 Reposition the cycle support arm so it is positioned slightly above horizontal. Position your cycle(s) into the saddle area of the frame locator. Pass the webbing strap over the frame of the cycle and thread through the metal loop. Pull the strap back tightly and press the hook and loop fastener to secure. Note: there must be a minimum 45mm of overlap (See Diagram). If the straps supplied with this product are not suitable, longer straps are available as an accessory. Please contact your nearest Halfords store. IMPORTANT: Use the red webbing straps to secure the cycle frame to the carrier. Failure to use these straps will result in the cycles falling off the carrier When carrying a second or third cycle, feed the RED straps around all cycles frames, and fully tighten. Failure to use these straps will result in the cycles falling off the carrier. To reduce obstruction from the handlebars, alternate the direction of each cycle during loading. FITTING 1 8 CAUTION: After the cycles are securely located on the carrier it is important to recheck the security of the carrier. If required, the clamping levers should be further tightened until the carrier is firmly fixed in all directions. 2 Halfords hi 3 bike instructions 6/8/07 12:05 PM Page 5 Halfords 6/8/07 12:05 Page 7 13 The cycle frame locators can be adjusted to best suit the angle of IMPORTANT: Do not open your boot/tailgate with the ...