Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Pending Copyright© 2007 CATEYE Co., Ltd. EL61RC-070620 066640131 1 *1 Dial Screw Release button Bracket rubber pad Bracket Bracket strap Light unit 2 3 4 6 ON OFF Hi Low Flash 2 sec. Double press Double press Switch Charge jack Battery charger To AC power outlet Battery indicator 1 2 Charging Indicator x1 #533-8827 H34 Bracket #534-1865 NiMH 4.8v 2700mAH UL:#534-1866 UK:#534-1867 EC:#534-1868 AS:#534-1870 CHR-2700mAH 4.8v NiMH SPARE PARTS 2 3 1 Screw Lens unit Battery Body Battery connector Rubber packing OK NO! Back side of lens Rubber packing Service & Research Address for USA CATEYE Service and Research Center 1705 14th St. 115 Boulder, CO 80302 Phone : 303.443.4595 Toll Free : 800.5CATEYE Fax : 303.473.0006 E-mail : service@cateye.com URL : CO.,LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn : CATEYE Customer Service Section Phone : (06)6719-6863 Fax : (06)6719-6033 E-mail : support@cateye.co.jp URL : Standard charging time Blinking red light : Charging Green light : Charging is completed Approx. 4 hours Charging indicator state ON - OFF : Long press Hi - Low : Single press Flash : Quick double press Hi : About 3 hours Low : About 9 hours Flash : About 36 hours Switch Standard continuous lighting time FOR SAFE OPERATION Do not place it within children's reach. In preparation for unexpected battery shutoff, we recommend you carry a dry-cell battery light unit with you. If the light unit or parts become dirty with mud, etc., clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result. Mount the light unit more than 10 cm away from the wireless meter. When it is mounted too close, the transmission may be affected adversely. This product has waterproof features that allow you to use it in rain. Do not use it soaked in water. Before Initial Use Before shipment, it is charged enough to check the light. Be sure to charge it before use, according to the instructions "How to charge." •• • • • INTRODUCTION Before using the light, please read this manual and the attached “NiMh Batteries” thoroughly, and keep them for future reference. Thank you very much for purchasing the CATEYE "SINGLE SHOT PLUS HL-EL610RC." This product is a high power rechargeable light unit that integrates a high power LED and a nickel metal-hydride rechargeable battery into a compact body. SPECIFICATIONS Light source High power white LED x 2 Battery NiMH 4.8v 2700mAH Battery charger CHR-2700mAH 4.8v NiMH Operating time Hi : Approx. 3 hours Low : Approx. 9 hours Flash : Approx. 36 hours Standard charging time Approx. 4 hours Temperature range Charging : 32°F – 104°F (0°C – 40°C) Operating : 5°F – 113°F (-15°C – 45°C) Recharge/discharge number of times About 300 times (until the rated capacity drops to 50%) Dimensions/weight 4-3/32” x 2-29/32” x 1-11/16” (104 x 74 x 43 mm) / 8.92 oz (253 g) * The specifi cations and design are subject to change without notice. 3 How to charge Open the charge jack cover at the back of the light unit to connect the battery charger plug. Plug the battery charger to an AC outlet. After charging, remove the plug and close the charge jack cover. 1.. 2.. 3.. HOW TO MOUNT HOW TO REPLACE BATTERY HOW TO USE 1 Lighting (lighting pattern selection) The lighting pattern is selected using a switch. Be sure to use the special purpose battery charger. Charging and lighting times are approximate values, and will vary by environmental and user conditions. * * 2 Remaining battery capacity When the battery indicator lights up red, the battery is almost shutoff. Charge the battery as soon as possible. COMPONENTS Light unit H34 Bracket Battery charger Wrap the bracket strap around the handlebar, and put it in the dial. Securely tighten the strap by turning the dial. Cut off the excess bracket strap extending from the dial. I n s e r t t h e l i g h t u n i t t o the bracket until it clicks. To remove, pull out while pressing the release button. CAUTION!: Make sure to tighten the dial by hand. If you tighten it too hard with a tool, the screw threads may be stripped. When the angle adjustment on the right and left sides is loose, tighten the screw (*1). Round off the cut edge of the bracket strap to prevent injury. How to Adjust Beam Angle Slightly loosen the dial on the bracket. Adjust the light unit angle so that the light is not directed to oncoming cars. When the dial is too fi rm to loosen, wash it slightly with water to loosen it. Do not loosen the dial too much, or the bracket strap may come off. Loosen the dial just enough to allow the bracket to move slightly. Securely tighten the dial after adjusting the strap. It can also be adjusted 10 degrees to the left and right. 1.. 2.. 3.. 4.. • • • 5.. 6.. * * * Turn over the light, and remove the 2 screws at the front of the lens using a 2.5 mm Allen wrench. Slowly pull out the lens unit from the body. Remove the battery connector connected to the boa...