Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Cateye Dateigröße: 1.77 mb Dateiname: de815b96-2b9f-465e-b3b8-b1ffc14266e3.pdf Unterrichtssprache:

Nos. 5236759/6957926 Pat./Design Pat. Pending 0678 Copyright© 2008 CATEYE Co., Ltd. CCRD4DW-081030 066600620 2 ENG Tire circumference reference table Tire size L (mm) 12 x1.75 935 12 x1.95 940 14 x1.50 1020 14 x1.75 1055 16 x1.50 1185 16 x1.75 1195 16 x2.00 1245 16 x1-1/8 1290 16 x1-3/8 1300 17 x1-1/4 (369) 1340 18 x1.50 1340 18 x1.75 1350 20 x1.25 1450 20 x1.35 1460 20 x1.50 1490 20 x1.75 1515 20 x1.95 1565 20 x1-1/8 1545 20 x1-3/8 1615 22 x1-3/8 1770 22 x1-1/2 1785 24 x1 (520) 1753 24 x 3/4 Tubular 1785 24 x 1-1/8 1795 24 x 1-1/4 1905 24 x 1.75 1890 24 x 2.00 1925 24 x 2.125 1965 26 x 7/8 Tubular 1920 26 x 1 (571) 1952 26 x 1-1/8 1970 26 x 1-3/8 2068 26 x 1-1/2 2100 26 x 1.0 (559) 1913 26 x 1.25 1950 26 x 1.40 2005 26 x 1.50 2010 26 x 1.75 2023 26 x 1.95 2050 26 x 2.00 2055 26 x 2.1 2068 26 x 2.125 2070 26 x 2.35 2083 26 x 3.00 2170 27 x 1 (630) 2145 27 x 1-1/8 2155 27 x 1-1/4 2161 27 x 1-3/8 2169 650 x 20C 1938 650 x 23C 1944 650 x 35A 2090 650 x 38A 2125 650 x 38B 2105 700 x 18C 2070 700 x 19C 2080 700 x 20C 2086 700 x 23C 2096 700 x 25C 2105 700 x 28C 2136 700 x 30C 2146 700 x 32C 2155 700C Tubular 2130 700 x 35C 2168 700 x 38C 2180 700 x 40C 2200 700 x 44C 2224 29 x 2.1 2288 29 x 2.3 2326 Preparing the computer 1 Clear all data (initialization) Press the AC button on the back. 2 Select the speed units Select “km/h” or “mph”. 3 Enter the tire circumference Enter the tire circumference of your bicycle in mm. * Refer to the tire circumference reference table. 4 Set the sensor ID Place the computer near the sensor. Pressing & holding RESET on the sensor displays the ID number on the screen, then moves to clock setting. * When setting the sensor ID, place the sensor at least 20 cm (approximately 8 inches) away from the computer. Press and hold the RESET button, the sensor will send the ID when releasing the button. * While setting the ID, the computer is on Standby for 5 minutes. If the computer does not receive any sensor signal, or you press and hold MODE during Standby, “ERROR” is displayed and the ID is canceled. You can continue to set up, but cannot measure. Be sure to set the ID according to “Sensor ID Setting” on the menu screen. * When the ID has been already set, the original ID is applied if you cancel the ID. 5 Set the clock When MODE is pressed and held, “Displayed time”, “Hour”, and “Minute” will appear, in this order. AC MENU MODE Before using the computer, please thoroughly read this manual and keep it for future reference. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:( 1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifi cations The FCC requires the user to be notifi ed that any changes or modifi cations made to this device that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate the equipment. AC km/h - mph Increase the value Move digits (by pressing & holding) Register the setting Register the setting Register the setting (fi nish) Move to Clock Setting when no ID has been set. Start the ID Setting (by pressing & holding) 24h-12h, or increase the value Switch the screen or move digits (by pressing & holding) Cancel the ID or reset (by pressing & holding) MENU MODE MENU MODE MODE MENU MENU MODE MODE MODE Battery case cover Push! When the computer is mounted on the bracket km/h mph : Speed unit : Wheel size icon : Sensor signal reception icon RESET 9 20 - 100 cm20 cm 1 2 3 4 5 mm 3 mm 3 7 6 5 3 mm 5 mm 2 1 1 2 4 8 8 2 How to install the unit on your bicycle 5 4 6 7 8 9 2 1 3 1 Bracket band 2 Bracket 3 Sensor (Speed/Cadence) 4 Nut 5 Wheel magnet 6 Cadence magnet 7 Sensor rubber pad 8 Bracket rubber pad 9 Nylon ties (x3) Install the sensor and magnet The clearance between the sensor face and magnet is less than 5 mm for Speed and 3 mm for Cadence, respectively. The magnet faces the sensor zone of the sensor. The distance between the computer and sensor is within the transmission range, and the mark on the sensor points to the computer. A Temporarily install the sensor / wheel magnet / cadence magnet Adjust and fi x the clearance between the magnet and sensor Rear wheel spoke Left crank Left Chain Stay Attach the bracket to the stem or handlebar When attaching the bracket to the stem When attaching the bracket to the handlebar * On account of the receiving sensitivity, attach the bracket so that the computer is kept horizontal. Click While supporting it by hand, push it out as if lifting the front up Cut Caution: Round off the cut edge of the bracket band to prevent injury. B C * Temporarily install the sensor and 2 magnets at the respective points that satisfy the condition B . When the condition cannot be satisfi ed, move the sensor in the front-and-rear direction to adjust. * Loosen the sensor screw to adjust the speed. After adjustment, fi rmly tighten the sensor screw and ...

Herunterladen

Geben Sie zwei Ziffern: