Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Please take special note of the following important points prior to choosing a location and beginning assembly of the Upright Exercise Bike. IMPORTANT SAFETY INSTRUCTIONS! . DO NOT locate the Exercise Bike outdoors, near swimming pools, or in areas of high humidity. . DO NOT operate your Exercise Bike if it has been dropped, damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services at the number in the Operation Manual. . DO NOT locate the Exercise Bike any closer than 30 inches ( 76 cm ) to a television set. . DO NOT locate additional Exercise Bike any closer than a minimum of 42 inches (107 cm) from center to center to avoid interference (cross talk) between Heart Rate monitors. . DO keep the area around your Exercise Bike clear of any obstructions, including walls and furniture. . DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the number listed in the Operation Manual. Save the shipping cartons in case of return. . DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use. . NE PAS placer le velo d’exercice allonge Lifecycle a l’exterieur, pres d’une piscine ou dans un endroit tres humide. . NE PAS faire fonctionner le velo d’exercice allonge Lifecycle s’il est tombe, s’il a ete endommage ou s’il a ete partiellement plonge dans l’eau. Telephoner au service apres-vente de Life Fitness dont le numero figure sur la couverture arriere du guide d’installation. . NE PAS placer le velo d’exercice allonge Lifecycle a moins de 76 cm (30 po) d’un poste de television. . MAINTENIR la zone autour du velo d’exercice allonge Lifecycle libre de toute obstruction, y compris murs et meubles. . VERIFIER si l’emballage contient toutes les pieces de la liste jointe avant de le mettre de cote. Si des pieces manquent, telephoner au service apres-vente de Life Fitness dont le numero figure sur la couverture arriere du guide d’installation. Conserver l’emballage au cas ou l’appareil devrait etre renvoye. . LIRE le manuel de l’utilisateur tout entier avant d’essayer de faire fonctionner cet appareil. Ceci est indispensable a son utilisation correcte. TOOLS REQUIRED FOR ASSEMBLY...Phillips screwdriver, T-45 Torx Driver, T-20 Torx Driver PARTS DESCRIPTION 1 Torx Button Mounting Bolt 3/8-16 x 3/4” Qty: 8 3 Accessory Tray Qty: 1 5 Top Cover Qty: 1 7 Left Seat Post Shroud Qty: 1 9 Left Pedal Strap Qty: 1 11 Handlebar Qty: 1 13 Power Supply Qty: 1 2 Phillips Pan Head Screw Qty: 12 8-18 x 5/8” Qty: 8 4 Console Assembly Qty: 1 6 Bottom Cover Qty: 1 8 Right Seat Post Shroud Qty: 1 10 Right Pedal Strap Qty: 1 12 Torx / Standard Screw #8-18 x 3/4” Qty: 1 14 Line Cord Qty: 1 1” 2” 3” 4” 5” 1 2 12 5 11 6 3 7 8 2 4 12 1 1 2 2 13 14 1. Locate the BOTTOM COVER (#6). Position the cover as shown with the notch of the center hole facing downward. Slide the BOTTOM COVER down over the UPPER CONSOLE SUPPORT TUBE (A) until it rests against the FRONT TUBE EXTENSION (B). 2. Position the HANDLEBAR (#11) as shown near the UPPER CONSOLE SUPPORT TUBE (A). 3. Connect the 4-PIN HEART RATE CONNECTOR (4P) leading from the HANDLEBAR (#11) center to the 4-PIN HEART RATE CONNECTOR (4P) leading from the UPPER CONSOLE SUPPORT TUBE (A). 4. Carefully slide the HANDLEBAR MOUNTING FLANGES (C) into the UPPER CONSOLE SUPPORT TUBE (A). NOTE: Be careful not to pinch the HEART RATE CABLE when inserting the HANDLEBAR FLANGES (C) into THE UPPER CONSOLE SUPPORT TUBE (A). MISE EN GARDE: Faites attention a ne pas pincer le CABLE de FREQUENCE CARDIAQUE en inserant les BRIDES de GUIDON (C) dans LE TUBE SUPERIEUR de SOUTIEN de CONSOLE (A). 5. Secure the HANDLEBAR (#11) to the UPPER CONSOLE SUPPORT TUBE (A) using four MOUNTING BOLTS (#1). Tighten the SCREWS to 15-20 ft. lbs. 6. Locate the TOP COVER (#5). Slide the BOTTOM COVER (#6) upward toward the HANDLEBAR (#11) until it contacts the HANDLEBAR. Position the TOP COVER over the HANDLEBAR and align it to the BOTTOM COVER. Secure the TOP COVER to the BOTTOM COVER using four PHILLIPS SCREWS (#2) as shown. 7. Align the ACCESSORY TRAY (#3) to the bottom of the DISPLAY CONSOLE (#4) as shown. Secure the ACCESSORY TRAY to the DISPLAY CONSOLE using four PHILLIPS SCREWS (#2). 8. Position the DISPLAY CONSOLE (#4) near the top of the CONSOLE SUPPORT ASSEMBLY (D). Remove the protective cover on the COAXIAL CABLE (CX). Carefully align and connect the COAXIAL CABLE to the coaxial connector located inside the rear of the DISPLAY CONSOLE. Align the LOCKING TABS of the 14-PIN CONNECTOR, 5-PIN CONNECTOR, and the 4-PIN CONNECTOR and plug them into the matching connectors located inside the rear of the DISPLAY CONSOLE until they snap securely into place. 9. Carefully feed the wires back into the top of the CONSOLE SUPPORT ASSEMBLY (D) and attach the DISPLAY CONSOLE (#4) to the CONSOLE SUPPORT A...