Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
No other use is intended or implied. Please follow the pictures on the front cover. Product Elements 1. Polar Bike Mount and Cycling Computer (picture 1 A) 2. Polar Speed Sensor, rubber part and spoke magnet (picture 1 B) Installing the Polar Bike Mount and Cycling Computer You can install the bike mount and the cycling computer on the left or right side of the handlebar or on the stem. 1. Place the rubber part on the handlebar or stem and insert the bike mount on top of it (picture 2). 2. Pass the cable ties over the bike mount and adjust them around the handlebar/stem. Secure the bike mount firmly. Cut off any excess cable tie ends (picture 2). 3. Position the cycling computer on to the bike mount. Turn the cycling computer clockwise until you hear a click. You can release the cycling computer by pressing it down and simultaneously turning it counter clockwise. Installing the Polar Speed Sensor To install the speed sensor and spoke magnet, you will need cutters and a cross-head screwdriver. 1. It is recommended to install the speed sensor on the front fork (as in picture 1) of your bicycle. Do not install the speed sensor on the seat stay if the (optional) power sensor is mounted. ENGLISH 2. Attach the rubber part to the speed sensor (picture 3). 3. Pass the cable ties over the speed sensor and rubber part (picture 4). Adjust the sensor to the front fork so that the POLAR logo faces outwards. Adjust the ties loosely. Do not tighten them fully yet. 4. Attach the magnet to a spoke at the same level as the speed sensor. There is a small caved dot at the backside of the sensor, which indicates the spot the magnet should be pointing at when passing the sensor. Fasten the magnet to the spoke and tighten it loosely with a screwdriver. Do not tighten it fully yet. Fine-tune the positioning of both the magnet and the speed sensor so that the magnet passes close to the sensor but does not touch it. Move the sensor towards the wheel/spokes as close as possible. The gap between the sensor and the magnet should be under 4 mm/0.16’’. The gap is correct when you can fit a cable tie between the magnet and the sensor. Rotate the front tire to test the speed sensor. The flashing red light on the sensor indicates that the magnet and the sensor are positioned correctly. Once the magnet and the speed sensor are positioned correctly, tighten the screw to the magnet with a screwdriver. Also tighten the cable ties securely and cut off any excess cable tie ends. Before you start cycling, set the wheel size of your bicycle into the cycling computer. ENGLISH Speed Sensor Teaching The cycling computer has to be coded to the Speed Sensor i.e. taught to receive speed and distance data. This enables exercising in a group without interference from other sensors. The cycling computer and sensor that come with the product set have already been synchronized but teaching is necessary when you start using a new sensor or if you use other bike settings than Bike 1. Install the speed sensor to your bike as advised. Before you start teaching, make sure that there are no other speed sensors or cycling computers nearby (40 m / 130 ft). The procedure only takes a few seconds. You can teach one sensor for each bike. Select Settings > Bike > Bike 1/2/3 > Speed. Select On/Off and On to turn the speed on. Press OK. Teach new sensor? is displayed. • Select YES to confirm teaching. Rotate the wheel a few times to activate the sensor. The flashing red light indicates that the sensor is activated. Completed is displayed once the teaching process is over. The cycling computer is now ready to receive speed and distance data. • Select NO to cancel the teaching. The teaching is cancelled and the cycling computer resumes contact with the previous sensor. To return to Time mode, press and hold the BACK button. ENGLISH Care and Maintenance Keep the speed sensor clean. Clean it with a mild soap and water solution and rinse off with clean water. Dry it carefully with a soft towel. Never use alcohol or any abrasive material such as steel wool or cleaning chemicals. Do not immerse the speed sensor in water. Your safety is important to us. Make sure that you can turn your handlebars normally and that the cable wires for brakes or gears do not catch the bike mount or the sensor. Also, make sure that the sensor does not disturb pedaling or using the brakes or gears. While riding your bike, keep your eyes on the road to prevent possible accidents and injury. Avoid hard hits as these may damage the sensor. Speed Sensor Battery Contact your authorized Polar Service Center for a replacement of speed sensor. Polar recycles used sensors. For more information on local after sales services, consult the Polar Customer Service Card. Frequently Asked Questions What should I do if... ...the speed reading is 0.0 or there is no speed reading while cycling? • Start searching for the data again by pressing and holding the LIGHT button and selecting Seek sensor. • Make sure the positio...