Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Tighten the bolt securely. (For a more secure fit, use a screwdriver.) Rubber Pad Rubber Pad Bolt under the bars on top of the bars Bracket (H-27) Bracket (H-27) Using the Extension spacer H-27 LS (Option) 1. Loosen the screw of the spacer and turn the spacer 180°. Tighten the screw securely again. 2. Insert the extension spacer to the lamp body from the rear. 3. When removing the lamp body from the bracket, remove it together with the extension spacer. Lamp Unit Slide Bracket Lamp Body Warning!!! Never touch the lamp body until thoroughly cooled. You may get burnt. 1. To install, slide the lamp body forward onto the lamp bracket until it clicks into position. Do the same thing with the switch. 2. To remove the lamp body, slide it backward while pushing the lever. Be sure to remove the switch together. Connecting the Jack After connecting the jack to the plug, wind the cord round the frame so that it will not hinder riding. Note: Securely connect the jack to the plug. HOW TO USE How to Switch on/off • To switch on/off, press the swicth button. • With the HL-NC250 TWIN, the two buttons operate as follows: Yellow Button: 20W Grey Button: 12W Note: In case the light does not turn on, charge the battery. Angle of Beam Switch on the light at night in flat place, and adjust the angle vertically. (It is also adjusted 10° horizontally.) To adjust, loosen the screw of the bracket a little. Warning!!! In addition to its high brightness, the beam is widely diffused. When using this light on public roads, be sure to adjust the angle downward so as not to blind oncoming traffic. Spacer Extension spacer (option) Lever Push Turn Slide Slide Switch Bracket: Attach the switch bracket (with the switch on it) on the handlebar. Be careful not to hinder the braking or shifting operation. 1. Use the appropriate rubber pad provided. Tighten the bolt. 2. To remove the switch from the switch bracket, slide it sideway while pushing the lever (as shown in the figure). * When removing the switch, remove the lamb body together. HOW TO MOUNT Mount the bottle battery into your bottle cage, the lamp body to the lamp bracket and the switch to the switch bracket. Connect the jack to the plug. Bottle Battery Insert the battery into your bottle cage and fix it tightly with the battery belts. Note: While riding, the bottle battery may jump out of the bottle cage by a strong impact. Be sure to fasten it securely with the belts. Switch Lever Switch Bracket Screw SLIDE Cord Bottle cage Bottle battery Belts REPLACING BOTTLE BATTERY By preparing a spare bottle battery, you can continue to use the light and the time for night riding will be extended. 1. Turn the battery cap counterclockwise and open it. 2. Disconnect the inside jack and replace the bottle battery. Note: After replacing, securely connect the jack again. Note: When closing the battery cap, be careful not to catch dust around the rubber ring. * The bottle battery can be charged without the battery cap. In this case, connect the plug of the charger directly to the jack inside of the bottle battery. HOW TO CHARGE Use only the included battery charger in an AC outlet for charging. 1. Insert the plug of the battery charger into the jack of the bottle battery (or the jack inside of the battery cap). 2. Plug the battery charger into an AC outlet. * The standard charging time is 8 hours if no charge is left in the battery. Never charge the battery for more than 24 hours; battery damage will result. 3. After charging, unplug the battery charger and pull out the plug. Note: Be sure to unplug the battery charger after charging. Note: To make full use of the bottle battery's capacity, recharge after the battery's whole capacity has been consumed. If the battery does not serve the proper run time even after it has a full charge it may be at the end of it's useful life. Replace it with a new one. Recharge / Discharge Number of Times: at least 500 (until rated capacity drops to 50%) HOW TO REPLACE THE BULB UNIT When replacing the bulb unit, disconnect the jack from the plug. Be sure the lamp body and the bulb have cooled before replacing. 1. Turn the socket holder counterclockwise and remove it. 2. Turn the lock ring counterclockwise and remove it. 3. Pull out the bulb unit from the lamp body and remove it from the unit holder. 4. Insert a new bulb unit into the unit holder and fix it with two screws. Note: Never touch the halogen bulb with bare-fingers; natural skin oils can cause the bulb to over heat and break. Never touch or wipe the inside of the reflective mirror. This may degrade the quality of the light output. 5. Make sure if the rubber ring A/B is properly aligned. Install the lock ring, and tighten it. 6. Install the socket holder and tighten it. Note: For the best performance of waterproofing, securely tighten all the parts. If water leaks into the inside of the bulb unit, it might result in damage of the components. SAFETY SYSTEM (AUTO-RESET FUSE) When an electrical surge/malfunction oc...
Dieses Handbuch ist für folgende Modelle:Fahrräder - HL-NC260 (222.29 kb)