Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Required Tools Obtain these tools before assembly: • Standard hex key set • Standard socket set • .-inch box wrench or crescent wrench • Flat head screwdriver • Phillips-head screwdriver • Needle-nose pliers • Standard torque wrench Installation Requirements Review these installation requirements before assembly: • The Cardio Theater Integrated Bracket is built to VESA MIS-D, 100/75 standard interface specifications. • Provide ample space around the climber. Open space around the unit allows for easier access and installation. • Open the box and assemble components in the sequence presented in this guide. • Leave room for adjustments. Tighten fasteners (bolts, nuts, and screws) so the unit is stable, but leave room for adjustments. Do not fully tighten fasteners until instructed in the assembly steps to do so. Assembly Tips • Read all the notes on each page before completing that step. • While you may be able to assemble the Cardio Theater Bracket using the illustrations only, important safety notes and other tips are included in the text. The assembly of the Cardio Theater Bracket takes about . hour to complete. Preparations page 4 Cardio Theater Integrated Bracket Assembly Instructions 3Install the Bracket Assembly The illustration shows how the Cardio Theater Bracket will look after you install it on the climber. CAUTION: Turn OFF the climber and remove the power plug from its power source before proceeding with the assembly. Install the Bracket Assembly page 5 Cardio Theater Integrated Bracket Assembly Instructions 1. Remove the bracket cover. Loosen the bolts on the ....-inch hex key. Pull the bracket cover away from the assembly. Set it aside. 2. Feed the coaxial/power cable with connectors through the bracket assembly. Set the bracket assembly aside. Important: Make sure you feed the cable so the end with the three connectors appears out of the top of the bracket assembly. Bracket cover Bracket assembly Bracket cover 1 2 Bracket assembly Top of bracket assembly Power connector DVD connector (optional accessory) Coaxial/power cable with its connectors Coaxial connector Install the Bracket Assembly page 6 Cardio Theater Integrated Bracket Assembly Instructions 3. Pull up the rubber boot along the support until you have about a boot and side covers. 4. Remove the three fasteners that display console to the upright support. Rest the display console between the handlebars. 5. Remove the plastic plug in the upright support. 3 4 Remove three fasteners. Rubber boot Display console 5 Remove plastic plug. Upright support Side covers Install the Bracket Assembly page 7 Cardio Theater Integrated Bracket Assembly Instructions 6. Feed the coaxial/power through the upright support. Ask your assistant to hold close while you insert the cable and its connectors into the upper hole support. Slide the cable down until you can access the connectors through the lower Note: You may need to move the ribbon cable inside the upright support to gain clear access. 7. Pull the cable and its connectors out of the lower hole. If needed, use a needle-nose pliers to grasp the cable. Note: While you pull about 3 feet (1 meter) of cable out of the lower hole ask your assistant to align the bracket assembly with the mounting fasteners on the upright support. Make sure the bracket assembly slides into place along the outside of the upright support. 8. Attach the bracket assembly and replace the fasteners. Ask your assistant to continue holding the bracket assembly, while you replace the three fasteners removed in step 4. Securely tighten all three screws using a ....-inch hex key. Install the Bracket Assembly 6 7 8 Bracket assembly Rubber boot Coaxial/power cable (with coaxial and power connectors) Display console Upright support page 8 Cardio Theater Integrated Bracket Assembly Instructions 4Feed the Cable through the Base 1. Use a Phillips-head screwdriver to remove 16 screws that hold the side covers on the Set the screws aside. 2. Slide both side covers up and away from the base of the unit. 3. Feed the coaxial/power cable and its connectors into the internal upright frame tube that does not contain the ribbon cable. 4. Pull the cable and both connectors out from the base of the tube and attach the power extension cable to the power connector. 1 2 3 4 Power connector Power extension cable Feed the Cable through the Base page 9 Cardio Theater Integrated Bracket Assembly Instructions 5. Snap the coaxial/power cable clips as you feed out the front of the unit. 6. Reassemble the side covers. display, the right side cover must be placed into position first. The left side cover fits into it. Note: Check the connectors on the coaxial/ power cable to make sure they are easily accessible. 7. Replace the 16 screws removed in step 1 and reposition the rubber boot. 5 6 7 Coaxial/power cable (with power extension cable) Right side cover Clip Front of the unit Power extension connector Replace the side cover screws and lower the rubber boot. Coa...