Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
The following Parts Identification Listing and the step by step installation procedures have been assembled to make the set-up of your exercise bike as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Lifecycle exercise bike… S A F E T Y F I R S T ! . DO NOT locate the Lifecycle 9100 exercise bike outdoors, near swimming pools, or in areas of high humidity. . DO NOT operate your Lifecycle 9100 exercise bike if it has been dropped, damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services at the number on the back page of this Installation Instruction Guide. . DO NOT locate the Lifecycle 9100 exercise bike any closer than 30 inches ( 76 cm ) to a television set. . DO NOT locate additional Lifecycle 9100 exercise bikes any closer than a minimum of 42 inches ( 107 cm ) from center to center to avoid interference (cross talk) between Heart Rate monitors. . DO keep the area around your Lifecycle 9100 exercise bike clear of any obstructions, including walls and furniture. . DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the number listed on the back page of this Installation Instruction Guide. Save the shipping cartons in case of return. . DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use. TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, 1/2” wrench PARTS DESCRIPTION 1 STABILIZER/HANDLEBAR BOLT Qty:3 0017-00101-0933 2 CONSOLE SCREW Qty: 4 0017-00101-1104 3 SEAT ASSEMBLY Qty: 1 AK18-00127-0000 4 COLLAR Qty: 1 0K18-01156-0002 5 HANDLEBAR ASSEMBLY Qty: 1 AK49-00015-0000 6 DISPLAY CONSOLE ASSEMBLY Qty: 1 AK49-0008-0001 7 STABILIZER BAR Qty: 1 AK18-0070-0000 8 9V ALKALINE BATTERY Qty: 1 0017-00003-0573 Step 1 Before proceeding, familiarize yourself with the parts of the Lifecycle 9100 exercise bike and make sure that you have received all the items described in the Parts List. Step 2 Remove the STABILIZER BAR (#7) from the carton base. Use the empty CONSOLE CARTON to raise the rear of the LIFECYCLE exercise bike as shown. Remove the two BOLTS (#1) from the bottom of the SHIPPING STABILIZER, save the BOLTS and store the SHIPPING STABILIZER with the other shipping containers. Step 3 Use the same two BOLTS that held the SHIPPING STABILIZER in place to attach the STABILIZER BAR as shown. Make certain that the BOLTS are tight and the STABILIZER BAR is flush against the frame. Remove the shipping carton. Step 4 Unfold the CONSOLE WIRE HARNESS from the POST extending from the FRAME. NOTE: THE COLLAR (#4) SHOULD ALREADY BE IN PLACE INSTALLED ON THE HANDLEBAR ASSEMBLY (#5). IF NOT, INSTALL BEFORE PROCEEDING. Step 5 Place the HANDLEBAR ASSEMBLY on the floor in front of the FRAME with the two CONNECTORS next to each other. Align the two CONNECTORS and push them together until they firmly snap into place. Step 6 Position the HANDLEBAR ASSEMBLY, with the COLLAR (#4) in place, so that the HANDLEBAR is facing away from the user. Slide the HANDLEBAR ASSEMBLY into the HANDLEBAR POST. Be careful not to pinch the wires. Align the three holes in the HANDLEBAR ASSEMBLY, with those in the HANDLEBAR POST and install the three HANDLEBAR BOLTS (#1). NOTE: BE CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES. TIGHTEN THE BOLTS SECURELY. Step 7 Slide the COLLAR (#4) down until it completely covers the HANDLEBAR ASSEMBLY HARDWARE and the HANDLEBAR POST. Secure the COLLAR by squeezing the sides and pushing downward firmly. Step 8 There is a large hole in the rear of the DISPLAY CONSOLE (#6) through which you can see a 16-PIN CONNECTOR and a 3-PIN CONNECTOR. These correspond to the matching CONNECTORS on the WIRE HARNESS protruding from the top of the HANDLEBAR. Properly align the locking tabs of the 16-PIN CONNECTOR on the WIRE HARNESS with the 16-PIN CONNECTOR on the back of the DISPLAY CONSOLE, then snap them together. Next, align the locking tabs of the 3-PIN CONNECTOR on the WIRE HARNESS with the 3-PIN on the back of the DISPLAY CONSOLE and plug them together until they SNAP into place. Step 9 Feed the WIRE HARNESS back into the HANDLEBAR TUBE. Attach the DISPLAY CONSOLE to the HANDLEBAR ASSEMBLY using the four CONSOLE SCREWS (#2) and a Phillips screwdriver. Tighten the four SCREWS in a crisscross pattern. CAUTION!: BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS. Step 10 To install the 9-VOLT ALKALINE BATTERY (#8) found in the parts bag use a Phillips screwdriver to remove the screw from the back door. Gently pull the BATTERY WIRES from the back of the DISPLAY CONSOLE and connect them to the 9-VOLT ALKALINE BATTERY. Carefully, tuck the BATTERY WIRES back into the DISPLAY CONSOLE and set the BATTERY in place. NOTE: ONLY USE AN ALKALINE TYPE BATTERY. USE OF ANY...