Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
When operating the remote control, it must be pointed at the logset inside the electric stove and a beep must be heard each time you press a function button. The beep confirms the remote control is performing the function you have requested. Note: Make sure your batteries are fully charged and installed correctly in your remote control. 3. POWER ON/OFF button at the top left is the main ON/OFF power button. Pressing this button you will hear a beep; this activates the power to the unit. Note: If the flame does not come immediately, press the DISPLAY ON/OFF button. 4. The two LOGSET buttons control the brightness of ember bed, which changes the brightness of your logset. To increase the brightness, press and release the BRIGHTER button. Each time you press this button you will hear a beep, and the brightness will increase by a small amount, until the maximum is reached. To decrease the brightness, press and release the DIMMER button. Each time you press this button you will hear a beep and the brightness will decrease by a small amount, until the minimum brightness is reached. Infrared Ray Exit FLAME TEMP. CONTROL POWER ON/OFF ON/OFF ON/OFF HIGH MED LOW LOWER HEATER DISPLAY HIGHER Dimmer Brighter EMBERS/ LOGSET Indicator Light 5. Heater Button: To activate the heater, press the heater button, then press HI, MED or LO. The heater is per-set to the following temperatures: HIGH will shut off when room reaches approximately 86° F (30 C) MED will shut off when room reaches approximately 75° F (24 C) LO will shut off when room reaches approximately 64° F (18 C) 6. To adjust the intensity of the flame, press the two buttons labeled HIGHER and LOWER under FLAME. To increase the flame intensity, press and release the HIGHER button. Each time you press the button you will hear a beep and the size of the flame will increase slightly until the maximum setting is reached. To decrease the flame intensity, press and release the LOWER button. Each time you press this button you will hear a beep and the size of the flame will decrease slightly until the minimum setting is reached. 7. To use the stove as a heater without the flame, press the LOGSET DISPLAY ON/ OFF button to turn the flame off and press the HEATER ON/OFF button to turn the heater on (if the heater was in the OFF position). Press the LOGSET DISPLAY ON/OFF button again to turn the flame back on. Press HEATER ON/OFF button again to turn the heater off. Note: You may have to re-adjust your desired flame setting (see step 6). 8. To turn off the stove, press the POWER ON/ OFF button once. When you hear the beep, the fireplace will be completely off and the flame will disappear. When you restart the fireplace with the remote control, all of the features you had set will remain in effect. NOTICE: This remote control must remain within 8 meters or 26 feet of the fireplace to be effective. IMPORTANT: If the flame does not activate after the POWER ON/OFF button is pressed, press the DISPLAY ON/OFF button to activate the flame. If the flame does not appear, repeat step 4, page 8. Figure 4 - Remote Control For Electric Fireplace 117190-01A CLEANING AND MAINTENANCE WARNING: Always disconnect power and allow the heater to cool before performing any cleaning,maintenanceorrelocation of this heater. Turn controls to OFF and remove plug from outlet or turn off circuit breaker to heater. Turn off heater and circuit breaker to heater before performing any cleaning and/or maintenance. Allow heater to cool completely. BULB REPLACEMENT WARNING: The halogen light bulbs in your unit can become extremely hot. Allow at least 10 minutes between turning off the heater and removing the light bulbs to avoid accidental burns. There are a total of 7 ( halogen light bulbs (type GX6.35 rated 120 volts, 35 watts) in your unit. • 2 bulbs provide illumination for the ember bed beneath the log set • 2 bulbs provide illumination for the flame generation assembly • 1 bulb provides illumination for the top contrasting light • 2 bulbs for replacement Most halogen light bulbs are rated to last approximately 1800 hours. Like all light bulbs, halogen bulbs require periodic replacement. When the bulbs in your unit have burned out you will notice or more of the following: • Contrasting light is dark • Flame is dim or dark in certain areas • Log set ember bed appears dim or dark in certain areas WARNING: Do not install replacement bulbs that exceed specified maximum watts. Your unit must be opened in order to replace the light bulbs. To reduce the number of times you need to open the unit, replace all bulbs at the same time. Removing Top of Unit 1. Unplug unit from the power supply. 2. Remove the two screws at the rear of the unit which secure ...
Dieses Handbuch ist für folgende Modelle:Kochfelder - CGESBL (456.26 kb)
Kochfelder - CGESBL (456.26 kb)
Kochfelder - CGESBL (456.26 kb)
Kochfelder - CGESBL (456.26 kb)