Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Hold the door trim (B) on the top edge of the door at the two sides and push inwards to release the clip seal. 2. Pull the door trim to the front to remove it. B 3. Hold the door glass panels on their top edge one by one and pull them upwards out of the guide 4. Clean the door glass panels. To install panels follow the procedure in reverse. Insert the smaller panel first, then the larger. Oven Ceiling You can fold down the heating element on the oven ceiling to clean the oven ceiling easily. WARNING! Before you fold down the heating element switch off the appliance. Make sure that the appliance is cold. There is a risk of burns! Oven - Care and Cleaning 23 Folding down the heating element 1. Remove the shelf support rails. 2. Hold the heating element with the two hands at the front 3. Pull it forwards against the spring pressure and out along the support on both sides. 4. The heating element folds down. The oven ceiling is ready to clean. Installing the heating element 1. Install the heating element in opposite sequence. Install the heating element correctly on the two sides above the support on the inner wall of the oven. 2. Insert shelf support rails. Removing the drawer The drawer underneath the oven can be removed for easier cleaning. Removing the drawer 1. Pull the drawer out as far as possible. 2. Lift the drawer slightly, so that can be lifted upwards at an angle of the drawer guides. Inserting the drawer 1. Set the drawer on the drawer's support rails. Make sure that drawer's middle guide engages into the middle rail. 2. Lower the drawer to the horizontal and push it in. WARNING! When the oven is in use, heat can build up in the drawer. For this reason, do not keep flammable things in there such as e.g. cleaning materials, plastic bags, oven gloves, paper, cleaning sprays, etc. Oven lamp WARNING! There is a danger of electrical shock! Before you change the oven lamp: • Switch off the oven. • Remove the fuses in the fuse box or switch off the circuit breaker. 12 24 24 What to do if… Put a cloth on the bottom of the oven for protection of the oven light and glass cover. Replacing the oven light bulb/cleaning the glass cover 1. Turn the glass cover anti-clockwise to remove it. 2. Clean the glass cover. 3. Replace the oven light bulb with applicable 300°C heat-resistant oven light bulb. 4. Install the glass cover. WHAT TO DO IF… Problem The residual heat indicators does not come on The appliance does not operate The oven does not heat up The oven does not heat up The oven lamp does not operate Steam and condensation settle on the food and in the oven cavity Possible cause The cooking zone is not hot because it operated only for a short time The fuse in the fuse box is released The oven is not switched on The necessary settings are not set The oven lamp is defective You left the dish in the oven for too long Remedy If the cooking zone must be hot, speak to the after sales service Control the fuse. If the fuse is released more than one time, refer to a qualified electrician. Switch on the oven Control the settings Replace the oven lamp Do not leave the dishes in the oven for longer than 15-20 minutes after the cooking process ends If you cannot find a solution to the problem yourself, contact your dealer or the service centre. The necessary data for the service centre is on the rating plate. The rating plate is on the front frame of the oven cavity. We recommend that you write the data here: Model (MOD.) Product number (PNC) Serial number (S.N.) ......................................... ......................................... ......................................... INSTALLATION First read "Safety information" chapter carefully. Environment concerns 25 Technical Data Appliance class 2, sub class 1 and class 1. Dimensions Height 850 mm Width 600 mm Depth 600 mm Oven capacity 58 l WARNING! Do not set the appliance on a base Levelling Use small feet on the bottom of appliance to set same level of cooker top surface with other surfaces Electrical installation WARNING! Only a qualified and competent person must do the electrical installation. The manufacturer is not responsible if you do not follow safety precautions from chapter "Safety". This appliance is supplied without a main plug and a main cable. Applicable cable types : H07 RN-F, H05 RN-F, H05 RRF, H05 VV-F, H05 V2V2-F (T90), H05 BB-F ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop...