Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
No use aceites detergentes, aditivos de aceite, ni aceites para herramientas neumaticas. Los aceites para herramientas neumaticas contienen solventes que pueden averiar los componentes internos de la herramienta. 3. Despues de agregar aceite, haga funcionar la herramienta brevemente. Limpie todo exceso de aceite que salga del orificio de salida de aire. CONEXION RECOMENDADA La ilustracion de abajo le muestra la conexion recomendada para la herramienta. 1. El compresor de aire debe tener la capacidad de suministrar un minimo de 4,14 bar cuando la herramienta este en uso. Si el suministro de aire es inadecuado podria haber perdida de potencia y falta de consistencia en el funcionamiento. 2. Puede utilizar un lubricador para lubricar la herramienta. Igualmente, puede utilizar un filtro para remover las impurezas liquidas y solidas que podrian oxidar u obstruir las partes internas de la herramienta. 3. Use mangueras de aire de 9,5mm (3/8”) disenadas para presiones Manual de Instrucciones Modelo SN318K00 20 Sp Operating The Tool (Continued) 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The tool MUST NOT OPERATE. Do not use the tool if it operates without pulling the trigger. Personal injury may result. 6. Remove tool from the work surface. The Work Contact Element (WCE) must return to its original down position. Pull the trigger. The tool MUST NOT OPERATE. Do not use the tool if it operates. Personal injury may result. 7. Depress the Work Contact Element (WCE) against the work surface. Pull the trigger. The tool MUST OPERATE. LOADING/UNLOADING THE TOOL 1. Always connect the tool to the air supply before loading fasteners. 2. Push down on the latch button. Pull back on the magazine cover. 3. For staples, load a clip of staples with the crowns straddling the magazine rail. 4. Push the magazine cover forward until latch button pops up. 5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air supply before unloading. ADJUSTING THE FASTENER PENETRATION 1. Regulate the air pressure to 60 psi at the tool. 2. Connect the air supply and test for penetration by driving fasteners into a sample piece of wood. If the fasteners do not achieve the desired penetration, adjust the air pressure to a higher setting until the desired penetration is achieved. Do not exceed 100 psi at the tool or durability of the tool will be reduced. ADJUSTING THE DIRECTION OF THE EXHAUST The tool is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. CLEARING A JAM FROM THE TOOL 1. Disconnect the air supply from the tool. 2. Remove all fasteners from the magazine (see "Loading/ Unloading The Tool"). Failure to do so will cause the fasteners to eject from the front of the tool when the nose assembly is removed. 3. Remove (3) cap screws from the nose of the tool. Remove nose plate, spacer and Work Contact Element (WCE) to expose jammed fastener. 4. Reinstall nose assembly in reverse order in step #3. 5. Make sure the trigger and Work Contact Element (WCE) move freely up and down without sticking or binding. Technical Support Please call our Tool Hotline at 1-800-543- 6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual. Fastener And Replacement Parts Use only genuine Campbell Hausfeld 18 gauge fasteners (or equivalent - see Fastener Interchange Information). Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number. Tool Repair Only qualified personnel should repair the tool, and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently. Assembly Procedure For Seals When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W nondetergent oil or equivalent, must be added through the air line before testing. Operating Instructions Model SN318K00 5 2. Saque todos los sujetadores del cargador (Vea la Seccion Carga- Descarga). 3. Cerciorese de que el gatillo y el elemento de contacto se muevan libremente en ambos sentidos sin atascarse o pegarse. 4. Reconecte la herramienta a la fuente de suministro de aire. 5. Presione el Elemento de Contacto de Trabajo contra la superficie de trabajo sin apretar el gatillo. La herramienta NO DEBE OPERAR. No use la herramienta si opera sin apretar el gatillo. Se pueden producir lesiones personales. 6. Remueva la herramienta de la superficie de trabajo. El Elemento de Contacto de Trabajo ti...