After pressing the 0 symbol, the indications turn off. Changing or cancelling the time Press the 0 symbol, the U indicator lights up. Change the time using the 1 to 9 symbols or press 0 to cancel. Cleaning lock function Cleaning the control panel while the hob is on may change the locked for 35 seconds. The surface of the control panel can settings. now be cleaned without risk of changing the settings. In order to avoid this, the hob has a cleaning lock function. Note: The lock does not affect the main switch. The hob mayPress the >D symbol. A signal sounds. The control panel is be switched off when desired. Automatic time limitation If the hotplate remains in use for a long time and no changes The indicator goes out when any symbol is pressed. The are made in the settings, the automatic time limitation function hotplate can now be reset. is triggered. When the automatic time function is used, it is governed by the The hotplate stops heating. The ”‰ symbol and the residual selected power level (from 1 to 10 hours). heat indicator oe/• flash alternatively in the display. Basic settings The device has several basic settings. These settings may be adapted to the user's individual needs. Indicator Function ™‚ Childproof lock ‹ Deactivated.* ‚ Activated. ™. Audible signals ‹ Confirmation and error signals deactivated. ‚ Only confirmation signal deactivated. . All signals activated.* ™† Automatic programming of cooking time ‹ Switched off.* ‚-SS Automatic shut-off time. ™‡ Duration of the time program function warning signal ‚ 10 seconds*. . 30 seconds. „ 1 minute. ™. Power-Management function ‹ = Deactivated.* ‚ = 1,000 W. minimum power. ‚= 1,500 W. . = 2,000 W. etc. S or S. = maximum power of the hob. ™S Hotplate time selection ‹ Unlimited: the last hotplate programmed remains selected.* ‚ Limited: The hotplate will only remain selected for 10 seconds. ™‹ Return to basic settings ‹ Personal settings.* ‚ Return to factory settings. *Factory settings Accessing the basic settings 3. Touch the 0 symbol repeatedly until the required function appears in the display. The hob must be switched off. 4. Then select the required setting from the control panel. 1. Switch on the hob using the main switch. 2. Within the next 10 seconds, touch and hold the 0 symbol for 4 seconds. In the display, ™‚ appears on the left and ‹ appears on the right. 5. Touch and hold the 0 symbol for at least 4 seconds. The settings have been saved. Leaving the basic settings Turn off the hob with the main switch. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cool enough before attempting to clean it. Only use cleaning products specifically designed for hobs. Follow the instructions provided on the packaging. Do not use: ¦ Undiluted washing-up liquid ¦ Dishwasher detergent ¦ Abrasive products ¦ Corrosive products such as oven sprays or stain removers ¦ Sponges that may scratch ¦ High-pressure or steam cleaners The best way to remove stubborn stains is to use a glass scraper. Follow the manufacturer's instructions. Suitable glass scrapers can be obtained through the Technical Assistance Service or from our online shop. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are usually due to small details. Before calling the Technical Assistance Service, you should consider the following advice and warnings. Indicator Malfunction Solution none The electric power supply has been cut off. Use other electrical appliances to check whether there has been a power cut. The appliance has not been correctly con-Check that the appliance has been connected correctly according to nected following the connection diagram. the connection diagram. Electronic system malfunction. If in the above checks, the malfunction is not resolved, contact the Technical Assistance Service. “ flashes The control panel is damp or an object is Dry the control panel area or remove the object. resting on it. “§ + number / Electronic system malfunction. Unplug the hob from the mains. Wait about 30 seconds before plug- s + number / ging it in again. * . + number * If the warning persists call the Technical Assistance Service. Do not rest hot pans on the control panel. Indicator Malfunction Solution ”‹ / ”S There is an internal error in the working. Unplug the hob from the mains. Wait about 30 seconds before plugging it in again. * ”. / ”† The electronic system has overheated and Wait until the electronic system has cooled down completely. Then the corresponding hotplate has been push any symbol on the hob.* switched off. ”… The electronic system has overheated and all hotplat...

Dieses Handbuch ist für folgende Modelle:
Kochfelder - PIL975N14E/21 (506.2 kb)