Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
WARNINGS! Particular attention shall be given to the relevant requirements regarding ventilation. This product should not be sealed into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for costs associated with releasing such a product, nor for repairing damage that may be incurred in doing this. When this product is installed it shall not be used as a space heater, especially if installed in boats or caravans. No combustible material or products should be placed on this product at any time. Do not spray aerosols in the vicinity of this product while it is in operation. CAUTION! This product must be installed according to these installation instructions and must comply with local building regulations, local gas authority codes and electrical regulations. Failure to install the product correctly could invalidate any warranty or liability claims. IMPORTANT! Read these instructions carefully before installing or using this product. Please make this information available to the person responsible for installing the product as it could reduce your installation costs. These products are registered: in New Zealand at and in Australia with AGA at Before You Start Prior to installation, ensure that the local distribution conditions (nature of gas and pressure) and the adjustment of the product are compatible. For adjustment conditions for this product see Gas Rate Summary. This gas hob must be connected to a 220V - 240V 50Hz power supply only and must be earthed via the power cord. Ensure a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. A means of disconnection with at least a 3 mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules, unless the local wiring rules allow for alternative means. Ensure that there is a power outlet within reach of the cooktop cable (900 mm from the rear right of the product). This must be accessible after installation. The mains cable should not touch any metal parts. Make the bench top of a heat resistant material. Seal exposed bare edges of the cutout with an oil-based paint or moisture proof polyurethane to prevent possible damage from moisture creeping between the cooktop trim and the benchtop. Dimensions A manifold centre line gas inlet B C F E J H G D Product CG603 series CG903 series CG913 series A Width 578 914 914 B Depth 511 533 546 C Height 40 40 76 Pan support 4343 22 to Benchtop Cutout CG603 series CG903 series CG913 series D Width 560 (558-562) 870 (846-882) 870 (860-882) E Depth 490 (485-495) 494 (478-501) 494 (486-524) F Radius R10 R10 R10 G 30 30 30 H 40 47 35 J Clearance to nearest combustible surface 60 60 81 Note: All measurements given in millimetres (mm). Cutout dimensions are given as an ‘ideal measurement’ e.g. for new cutouts, followed by an ‘otherwise acceptable range’ (in brackets) e.g. for existing cutouts or replacement products. Clearances a e c d b f g a 600 mm minimum from top of trivet to rangehood. 750 mm minimum from top of trivet to overhead exhaust fan. (Fisher & Paykel splashbacks are 750 mm high). b 600 mm minimum from top of trivet to downward facing combustable surface. (450 mm minimum if protected by tiles or fire resistant materials). CG603 SERIES CG903 SERIES CG913 SERIES c Clearance from side edge of 130 mm 120 mm 80 mm product to any combustible surface d Clearance from rear edge of 100 mm 90 mm 90 mm product to any combustible surface Clearance from rear edge of 10 mm 10 mm 10 mm product to any non-combustible surface e Clearance below benchtop to any 60 mm 60 mm 81 mm combustible surface Clearance below benchtop to 45 mm 45 mm 81 mm F&P DishDrawer® or F&P oven f Ensure there is an earthed power outlet within 900 mm of the rear right-hand corner of the product. When used with a flexible hose, the connector on the wall should be between 800 mm to 850 mm above the floor and in the region outside the width of the appliance to a distance of 250 mm. This should be accessible with the appliance installed. g When protecting a wall with non-combustible material it must be at least 150 mm high. Installation Instructions Standards Requirements Australian and New Zealand Gas Installation Standards (AS5601, NZS 5261) require a cooktop to be installed so that the surface temperature of any nearby combustible surface will not exceed 65oC above ambient. Typically this is achieved by: A Having the cooktop spaced away from the wall (see “Clearances” for dimensions) [Dimension c and d] OR B by protecting the wall, to at least 150 mm high [Dimension g] along it’s length, with non-combustible surface materials, such as: - 5 mm thick ceramic tiles alone are adequate. -Tempered glass or sheetmetal (min. 0.4 mm thick) is acceptable when used in front of a fire resistant material. - Fisher & Paykel Spl...