Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Remove spilled fluids immediately; don't let any food rests burn on. Keep the ventilation openings under the pan support clean. The ventilation openings must not be covered. Thoroughly dry the burners after cleaning. Only turn on the appliance once all parts are dry. Damp burner parts could cause problems with ignition or an unstable flame. When assembling the burner parts, pay attention to their correct positions (latching lugs). All parts must lie flat. Appliance part/ surface Recommended cleaning Stainless steel surfaces Apply dishwashing liquid – dry off with a soft cloth. Only use a little water for cleaning; no water must penetrate into the appliance. Soak burned-in grime in a little water and some dishwashing liquid. Do not scrub it off. Use our stainless steel cleaner ( order number 311413) to remove extreme soiling or yellow discoloration caused by heat. Pan supports Remove carefully for cleaning. Soak them in the sink. Clean with a dishwashing brush and dishwashing liquid. Clean carefully around the rubber buffers so they do not come loose. Rinse them with clear water and carefully dry them before putting them back in place. Do not wash them in a dishwasher! Burner parts (brass) Dishwashing liquid – dry with a soft cloth. Make sure openings are not clogged. Make sure that no small parts are lost. Do not wash them in a dishwasher! Control knobs Dishwashing liquid – the cloth must not be too moist. Wipe dry with a soft cloth. Clean the electrode A dirty electrode can disrupt ignition or flame monitoring. If required, clean it with the brush included. The electrode is sensitive. Clean it carefully. Do not twist or damage it. Do not switch on the cooktop while cleaning it. Burned-on grime For stubborn, burned-on grime, you can order a grille cleaner gel from your specialist shop or our customer service ( order number 463582) . It is suitable for pan supports, burner parts and the stainless steel cooktop. Leave on overnight if necessary. Bear in mind the notes on the cleaner. Burner discoloration After prolonged use, the brass burner parts go dark due to natural oxidation. The color changes has no impact on useful benefit. Proceed as follows to remove such discoloration: 1 Prepare a solution out of equal parts white vinegar with no more than 8 % acid ( domestic vinegar) and warm water. 2 Place the discolored burner parts in the solution for 10 minutes at most. Remove stubborn stains with a cloth or a sponge. 3 Then thoroughly rinse the burner parts with clear water and dry them well before their next use. 9 CAUTION Too high a concentration of solution or excessively prolonged contact of the burner parts with vinegar will damage the surface. Troubleshooting Yo u can o f ten eas ily elim inate p rob lems t hat m ay o c cu r on you r ow n. B efore callin g cus to m e r se r vice , 9 WARNING t ake into a ccou nt the fo llowi ng informat io n. Risk of electric shock I ncor rec t re pair s are dan gero u s. Re pair s m ay on l y b e c a rri ed out by one of ou r t r ai n e d af te rsa les e ng inee r s. I f th e a pp lianc e is fa ult y, u npl ug the m a ins plu g o r sw itc h of f th e f use in th e f use b ox . C o n ta c t th e a f ter- s a l es s e r vic e. Malfunction Cause Solution Burner does not ignite when No power supply. Turn all control knobs to 0. Check in the fuse box switched on. whether the fuse has blown. Burner does not ignite when Fault on the burner or the gas sup- Turn all control knobs to 0. switched on. Audible signal sounds. ply. Check: . Burner parts fitted correctly? . Gas shut- off valve open? . Burners dry and clean? . Air in the line after first connection or a change of gas cylinder (liquid gas)? . Gas cylinder empty (liquid gas)? Burner goes off during operation. Fault on the burner or the gas sup- Turn all control knobs to 0. Wait until the appliance Audible signal sounds. ply. has cooled down. Check: . Burner parts fitted correctly? . Electrode soiled (food remainders) or moist? . Burner soiled by spillovers? . Strong draft ( e.g. open window directly behind the gas stovetop) ? . Gas cylinder empty (liquid gas)? Burner goes off during operation. Protection against overheating Turn all control knobs to 0. Wait until the appliance Audible signal continues to has cooled down and the audible signal goes off. sound although all control knobs have been turned to 0. Burner goes off during operation. Power failure Turn all control knobs to 0. Check the power supply. The burners do not reignite automatically after a power failure. Turn the control knob to 0. The Technical defect Notify Gaggenau customer service. appliance tries to reignite and an audible signal sounds. Burners go off during operation. Safety shut-off: appliance has not Turn the control knob to 0 and then switch on again, An audible signal sounds. been operated in the past six hours. if necessary. There is a smell of gas in the Potential leak on connection of gas Check gas cylinder connection for leaks. kitchen. cylind...