Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
That is to say, the ignition is activated when the control knob is pressed briefly. After igniting, keep the control knob pressed for around 5-8 seconds more because the heat sensor that opens the gas channel has to warm up first. The gas hob has 1 normal burner (front burner) and 1 high-intensity burner (rear burner). All burners have a thermal protection device that prevents unburned gas from escaping in the open position. The total rated thermal load amounts to: 16000 BTU (4.7 kW) referred to Hs* (gross calorific value) 14300 BTU (4.2 kW) referred to Hi (calorific value) The specified rated load is defined by installation of the fixed nozzles. The gas hob is converted to a different gas type by nozzle replacement (full and low-burning nozzles) (see nozzle table on p. 12). The symbols on the control panel mean: 0 Off High setting Low setting The flame is infinitely variable between high and low-setting. Maintenance Instructions – Keep appliance area clean and free from combustible materials, gasoline and other inflammable vapors and liquids. – Do not obstruct the flow of combustion and ventilation air. – Visually check burner flames with this pictorial representation (see figure 4). 8 Fig. 4 High Off Low 3. Operation Fig. 5 Fig. 6 The cooking positions must only be ignited when all burner parts are fitted. Otherwise, malfunctions may occur on the ignition unit. Switching on (Fig. 5): – Place a pot or a pan on the corresponding cooking position. – Fully press in the control knob for the corresponding cooking position. This activates the ignition. Keep the control knob pressed! –Turn the control knob to the left to the “high" position. If the flame should not ignite within 2 to 4 seconds, turn the control knob further to the left to the “low" position and then back to the “high" position after ignition. It is often faster to ignite in the low position because the various gases have a differing ignition response. After igniting, keep the control knob pressed for around 5-8 seconds more because the heat sensor that opens the gas channel has to warm up first. Repeat the operation if the flame should go out again. The flame size can be set continuously between full and low by slowing turning the control knob. Switching off (Fig. 6): Fully turn the control knob to the left to the 0 position on the left. Wipe off spilt food immediately, thus ensuring that it cannot burn in on the hob. Caution! The burner gets very hot during operation! Never use abrasive or caustic cleaning agents. You should only clean the control panel and the control knobs with detergent and a a soft cloth. To ensure perfect functioning, keep the thermal sensor and the spark plug clean. Keep the incoming air openings on the rear of the panel unobstructed and clean. Please thoroughly clean the appliance before operating it for the first time and after every use. – Wait until the appliance has cooled down. – Remove the pot grid. – Remove the burner cover. – Clean the hob, the burner covers and the pot grid with commercially available cleaning agents (not in a dishwasher!), e.g. with warm soap solution and a dishwashing brush. – Whenever required, clean the burner head with a moist cloth. – Soak burnt-in remainders in a little water and detergent. This loosens even the most stubborn of soiling. Do not use any abrasive agents and abrasive sponges. – As the result of heat development, slight discoloration can appear on the stainless steel surface. Do not attempt to scrape away such discoloration. This damages the surface. Distribute stainless steel care agents uniformly and thinly on the hob (not on the control panel!). This will ensure an even surface and will keep your hob in a good condition for a long period of time. Important: allow the burner covers to cool down before cleaning them! When assembling, place the burner cover (1) on the burner head (2) so that the four tabs on the bottom edge of the burner cover engage in the corresponding tabs on the burner head (see Fig. 7). Place the pot grids back in position. 4. Cleaning and care Caution: Never use high-pressure or steam jet units to clean your appliance because otherwise the electrical safety of the appliance will no longer be guaranteed. 10 Fig. 7 1 2 5. Maintenance 5.1 General 5.2 Remedying slight malfunctions yourself The appliance must be disconnected from the power supply during all repair work. In the event of malfunctions, check whether the gas and electricity supply is in proper working order, i.e. the gas valve is open and the plug has been plugged into the socket. If the power supply is functioning correctly, but your appliance still does not work, please contact your Gaggenau dealer who will provide you with the address and telephone number of your nearest manufacturer’s authorized service agent or contact Gaggenau USA on (800) 828-9165. Specify the appliance type (see rating plate). Repairs may only be carried out by authorised technicians, in order to guarantee the safety of t...
Dieses Handbuch ist für folgende Modelle:Kochfelder - VG232232CA/02 (565.55 kb)