Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Indicator Function ™ ‚ Childproof lock ‹ Off. * ‚ On. ™ . Sound signals ‹ Most sounds off. ‚ Some sounds off. . All sounds off. * ™ † Automatic timer ‹ Switched off. * ‚ - SS Automatic shut- off time ™ ‡ Duration of the time program function warning signal ‚ 10 seconds. . 30 seconds. „ 1 minute. *Factory settings Indicator Function ™ . Power- Management function ‹ = Deactivated. * ‚ = 1,000 W minimum power. ‚ . = 1,500 W. . = 2,000 W. etc. S or S. = maximum power of the plate. ™ ‰ Working without the Tipp- Pad ‹ Off. * ‚ On. ™ ‹ Return to default settings ‹ Personal settings.* ‚ Return to factory settings. *Factory settings To access the basic settings 3. Press the 3 symbol several times until the time program function screen displays the symbol for the desired function. The range should be turned off. 4. Then select the required setting using the Tipp control. 1. Turn on the range with the main switch. 2. Within the next 10 seconds, press the 3 symbol and hold for 3 seconds. The display of the time program function shows ™‚ y and the cooking area display shows ‹ . 5. Press the 3 symbol again and hold for more than 3 seconds. The settings will have been properly saved. Quit To leave the basic settings, turn off the hob at the main switch. Keep warm function The plate-warming plate is used for melting chocolate or butter, and for keeping food warm. To activate 1. Select the required hotplate using the Tipp control. 2. Within the next 5 seconds, press the – symbol. The – indicator lights up. The " keep warm" function has been turned on. To turn off 1. Select the required hotplate using the Tipp control. 2. Press the – symbol. The – display turns off. After five seconds, the hotplate turns off and the residual heat indicator appears. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cold enough before attempting to clean it. Only use cleaning products specifically designed for glass- ceramic hobs. Follow the instructions provided on the packaging. Do not use: ¦ Abrasive products ¦ heavy-duty cleaners, like oven sprays and stain removers ¦ Pads that may scratch ¦ High-pressure or steam cleaners Glass scraper Remove dried- on food remains using a glass scraper. 1. Release the scraper safety catch 2. Use the blade to clean the hob surface Do not attempt to clean the hob surface with the base of the scraper. This could result in scratching. a= Risk of injury! ! The blade is extremely sharp. Risk of cuts. Protect the blade when not in use. Replace the blade immediately when any imperfections are found. Care of the appliance Apply an additive to protect and preserve the hob. Follow the advice and warnings provided with the product. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper The Tipp control For cleaning the Tipp control, warm water and a little soap is recommended. Do not use abrasive or corrosive cleaning products. Do not clean the Tipp control in a dishwasher or in washing up water. Otherwise, it could be damaged. Fixing malfunctions Malfunctions are generally caused by minor faults. Before contacting the Technical Assistance Service, ensure you have read the following recommendations and warnings. Indicator Malfunction Measure none The electric power supply has been cut off. Check other electrical appliances to check whether there has been a power cut. The appliance has not been properly Check that the appliance has been connected properly according to connected following the connection the connection diagram. diagram. Electronic system malfunction. If the malfunction is not resolved by the above checks, contact the Technical Assistance Service. “ flashing The control panel is wet or an object is Dry the control panel area or remove the object. resting on it. “§ + number / Electronic system malfunction. Disconnect the range from the mains. Wait about 30 seconds, then s + number / connect it again. * . + number “§ „ ‰ The Tipp control was dragged instead of Wait a few seconds, then switch on the range and hotplate properly slanting it towards the required hotplate once again. ”‹ / ” S There is an internal error in the system. Disconnect the range from the mains. Wait about 30 seconds, then connect it again. * ” . The electronic system has overheated and Wait for the electronic system to cool down. Then push any symbol the related hotplate has been switched off. on the range. * ” … The electronic system has overheated and all of the hotplates have been turned off. * If the indicator persists, call the Technical Assistance Service. Do not rest hot pans on the control panel. Indicator Malfunction Measure —‚ Incorrect voltage supply...