Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
The control panel is locked for approximately 35 seconds. The surface of the control panel can now be cleaned without risk of changing the settings. After the time has elapsed, a warning beep will sound and after a few seconds the function is deactivated. The control panel lock has been deactivated. Note: The cleaning protection function does not include the >D symbol or the main switch. The hotplate may be switched off when required. Automatic time limitation If the hotplate remains in use for a long time and no changes The indicator goes out when any symbol is pressed. The are made in the settings, the automatic time limitation function hotplate can now be reset. is triggered. When the automatic time function is used, it is governed by the The hotplate stops heating. On the hotplate display, ” and ‰ selected power level (from 1 to 10 hours) . flash alternately. Basic settings The device has several basic settings. These settings may be adapted to the needs of the user. Indicator Function ™ ‚ Childproof lock ‹ Off. * ‚ On. ™ . Beeps ‹ Most signals deactivated. ‚ Some beeps deactivated. . All beeps activated. * ™ † Automatic timer ‹ Switched off. * ‚ - SS Automatic shut- off time ™ ‡ Duration of the time program function warning signal ‚ 10 seconds* . . 30 seconds. „ 1 minute. ™ . Power- Management function ‹ = Deactivated. * ‚ = 1,000 W minimum power. ‚ . = 1,500 W. . = 2,000 W. etc. S or S. = maximum power of the hob. ™ S Hotplate time selection ‹ Unlimited: the last hotplate programmed remains selected. * ‚ limited: The hotplate will only remain selected for 10 seconds. ™ ‹ Return to default settings ‹ Personal settings. * ‚ Return to factory settings. *Factory settings Accessing the basic settings 3. Press the 0 symbol until the indicator for the required function is displayed. The hob should be switched off. 4. Next select the setting required with symbols 0 to 9. 1. Turn on the hob with the main switch. 2. In the next 10 seconds, hold down the 0 symbol for 4 seconds. ™‚ is displayed on the left of the screen and ‹ on the right. 5. Press the 0 symbol for 4 seconds. The settings will have been properly saved. Leaving the basic settings Turn off the hob with the main switch. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cold enough before attempting to clean it. Only use cleaning products specifically designed for glass- ceramic hobs. Follow the instructions provided on the packaging. Do not use: ¦ Abrasive products ¦ heavy-duty cleaners, like oven sprays and stain removers ¦ Pads that may scratch ¦ High- pressure or steam cleaners Glass scraper Remove dried- on food remains using a glass scraper. 1. Release the scraper safety catch 2. Use the blade to clean the hob surface Do not attempt to clean the hob surface with the base of the scraper. This could result in scratching. a= Risk of injury! ! The blade is extremely sharp. Risk of cuts. Protect the blade when not in use. Replace the blade immediately when any imperfections are found. Care of the appliance Apply an additive to protect and preserve the hob. Follow the advice and warnings provided with the product. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are generally caused by minor faults. Before contacting the Technical Assistance Service, make sure you have read the following recommendations and warnings. Indicator Malfunction Measure none The electric power supply has been inter- Use other electrical appliances to check if there has been a power rupted. cut. The appliance has not been correctly con- Make sure that the appliance has been connected correctly. nected following the connection diagram. Electronic system malfunction. If in the above checks, the malfunction is not resolved, contact the Technical Assistance Service. * If the warning persists call the Technical Assistance Service. Do not place hot pans on the control panel. Indicator Malfunction Measure “ flashing The control panel is wet or an object is Dry the control panel area or remove the object. resting on it. “§ + number / Electronic system malfunction. Disconnect the hob from the mains. Wait 30 seconds or so, then con- s + number / nect it again. * . + number ”‹ / ”S There is an internal error in the system. Disconnect the hob from the mains. Wait 30 seconds or so, then connect it again. * ” . The electronic system has overheated and Wait until the electronic system has cooled down completely. Then the corresponding hotplate has been press any symbol on the hob. * switched off. ” … The electronic system has overheated and all hotplates have been switched off....
Dieses Handbuch ist für folgende Modelle:Kochfelder - PID675N14E/02 (1.28 mb)