Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
is triggered. When the automatic time function is used, it is governed by the The hotplate stops heating. The ” , ‰ symbol and the residual selected power level (from 1 to 10 hours) . heat indicator oe/ • flash alternately in the display. Displaying energy consumption This function displays total energy consumption for the time the The Basic Settings chapter provides information on activating hob has been switched on. this function. After switching off the hob, the consumption in kWh is displayed for 10 seconds. An example is shown in the image with a consumption of ‚ . ‹‰ kWh. Basic settings The device has several basic settings. These settings may be adapted to the user's individual needs. Indicator Function ™ ‚ Childproof lock ‹ Deactivated. * ‚ Activated. ™ . Audible signals ‹ Confirmation and error signals deactivated. ‚ Only error signal activated. . Only confirmation signal activated. „ All signals activated. * ™ „ Display energy consumption ‹ Deactivated. * ‚ Activated. ™ † Automatic programming of cooking time. ‹ Switched off. * ‚ - SS Automatic shut-off time. ™ ‡ Duration of the time program function warning signal ‚ 10 seconds* . . 30 seconds. „ 1 minute. ™ . Power- Management function ‹ = Deactivated. * ‚ = 1,000 W. minimum power. ‚ = 1,500 W. . = 2,000 W. etc. S or S. = maximum power of the hob. ™ S Hotplate time selection ‹ Unlimited: the last hotplate programmed remains selected.* ‚ Limited: The hotplate will only remain selected for 10 seconds. ™ ‹ Return to basic settings ‹ Personal settings.* ‚ Return to factory settings. *Factory settings Accessing the basic settings 4. Then select the desired setting with the programming zone. The hob should be turned off. 1. Switch on the hob using the main switch. 2. Within the next 10 seconds, press and hold the ' symbol for 4 seconds. In the display ™ and ‚ alternately light up and ‹ lights up as a default setting. 3. Press the ' symbol several times until the desired function indicator appears. 5. Press and hold the ' symbol again for more than 4seconds. The settings will have been correctly saved. Quit To leave the basic settings, turn off the hob at the main switch. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cool enough before attempting to clean it. Only use cleaning products specifically designed for hobs. Follow the instructions provided on the packaging. Do not use: ¦ Undiluted washing- up liquid ¦ Dishwasher detergent ¦ Abrasive products ¦ Corrosive products such as oven sprays or stain removers ¦ Sponges that may scratch ¦ High-pressure or steam cleaners The best way to remove stubborn stains is to use a glass scraper. Follow the manufacturer's instructions. Suitable glass scrapers can be obtained through the Technical Assistance Service or from our online shop. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are usually due to small details. Before calling the Technical Assistance Service you should bear in mind the following advice and warnings. Indicator Malfunction Solution none The electric power supply has been cut off. Use other electrical appliances to check whether there has been a power cut. The appliance has not been correctly connected following the connection diagram. Check that the appliance has been connected correctly according to the connection diagram. Electronic system malfunction. If none of the above checks resolve the malfunction, contact the Technical Assistance Service. * If the warning persists call the Technical Assistance Service. Do not rest hot pans on the control panel. Indicator Malfunction Solution The indicators The control panel is damp or an object is Dry the control panel area or remove the object. blink resting on it. “§ + number / s Electronic system malfunction. Unplug the hob from the mains. Wait about 30 seconds before + number / . + plugging it in again. * number ”‹ / ”S There is an internal operating error. Unplug the hob from the mains. Wait about 30 seconds before plugging it in again. * ”. / ” † The electronic system has overheated and Wait until the electronic system has cooled down sufficiently. Then the corresponding hotplate has been press any symbol on the hob. * switched off. ” … The electronic system has overheated and all hotplates have been switched off. —‚ Supply voltage outside normal operating Contact your power company. limits. —. / — „ The hotplate has overheated and has Wait until the electronic system has cooled down sufficiently before switched off in order to protect its cooking switching it back on. surface. * If the warning persists call the Technical Assi...