Type of connection: The appliance falls under protection class I and can only be used in combination with a grounding conductor connection. The manufacturer accepts no responsibility for any malfunction or damage caused by incorrect electrical installations. Installation: The appliance must be connected to a fixed installation and the means of disconnecting it from the fixed installation must be installed according to the installation instructions. Built-in assembly under worktop: The induction hobs may only be installed over a drawer, ovens with forced ventilation from the same brand and dishwashers from the same brand. Refrigerators, unventilated ovens and washing machines may not be installed beneath the hob. Power cable: Do not tie the power cable or pass it along sharp edges. If there is an oven installed below, pass the cable along the rear corners of the oven to the connection box. It must be positioned so that it does not touch any of the hot parts of the hob or the oven. Hob: flat, horizontal, stable. Follow the hob manufacturer's instructions. Warranty: an unsuitable installation, connection or assembly will invalidate the product warranty. Note: Any change to the appliance's interior, including changing the power cable, must only be performed by specially trained members of the Technical Assistance Service. Preparation of assembly kitchen units, figures 1/2/3/ 4 Built-in kitchen units: Minimum temperature resistance of 90° C. Gap: Remove any shavings after performing cutting work. Cut surfaces: Seal with heat resistant material. Assembly over drawer, figure 2a Metal objects stored inside the drawer could become very hot due to the air recirculating from the hob ventilation system. If this occurs, an intermediate support is recommended. Intermediate support: A wooden panel can be used ( figure 3) or you may order a suitable accessory from our Technical Assistance Service. The reference code for this accessory is 686002. Worktop: Must have a minimum thickness of 20 mm. The distance between the top of the working surface and the top of the drawer must be 65 mm. Assembly over oven, figure 2b Worktop: Must have a minimum thickness of: ¦ 20 mm if installed over a compact oven. ¦ 30 mm if installed over a full- size oven. If the hob is installed over a compact oven, there must be a distance of 60 mm between the top of the oven and the top of the working surface. Assembly over dishwasher, figure 2c An intermediate accessory must be installed. The accessory may be ordered from our Technical Assistance Service. The reference code for this accessory is 686002. Worktop: Must have a minimum thickness of 20 mm and maximum thickness of 40 mm. The space between the top of the working surface and the top of the dishwasher must be: ¦ 60 mm if installed over a compact dishwasher. ¦ 65 mm if installed over a full- size dishwasher. Ventilation, figure 4 Ventilating the hob requires: ¦ An opening on the upper part of the kitchen unit's rear wall ( figure 4a) . ¦ A separation between the rear part of the kitchen unit and kitchen wall (figure 4b) . Installing the appliance, figures 5/ 7 Fit the hob into place, (figure 5) Connect the appliance to the mains to check its operation. ¦ Voltage, see specifications plate. ¦ Connect based on the connection drawing only (figure 7) . 1. Brown 2. Blue 3. Yellow and green Position the hob in the gap available on the worktop with a depth of 500 mm, ( figure 6) 1. Mark the centre of the gap in the worktop. 2. Fit the hob into place. 3. Align the marks of the hob frame with those of the worktop. 4. Insert the hob. Changing the intensity of the 13 / 16 / 20 Ampconnection current, figure 8 Before using the hob for the first time, the intensity of the hob connection must be tested. Follow the steps below to change the current of the hob: 1. Turn on the hob with the main switch. Do not place any pans on the hotplates 2. Within the following 60 seconds, adjust all hotplates to the desired power level according to the required connection current ( see table). Power level Connection current in amperes ‚ 20 A . 16 A „ 13 A 3. Turn off all the hotplates in sequence, starting from the lower right and continuing counter-clockwise. 4. The selected connection current is indicated in the display of the right- hand lateral hotplates. 5. Turn off the hob with the main switch. The selected connection current will have been properly saved. Uninstalling the appliance Disconnect the appliance from the mains. Push the hob upwards from below to remove it. Caution! Damage to the appliance! Do not try to remove the appliance by prying it out from above. INSTRUCTION MANUAL Additional information on products, accessories, replacement parts and services can be found at siemens- home. com and in the online shop siemens- eshop. com : Safety precautions Please read this manual carefully. Please keep the instruction and installation manual as well as the appliance certificate in a safe place for later use...

Dieses Handbuch ist für folgende Modelle:
Kochfelder - EH645BE18E/01 (2.16 mb)
Kochfelder - EH645BE68X/01 (2.16 mb)