Login:
Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Anleitung Hotpoint, modell E6004

Hersteller: Hotpoint
Dateigröße: 573.5 kb
Dateiname: ac015928-5be5-4ef5-aff9-540a8ce072cb.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


• Oven chemical cleaners, aerosols and oven pads Caustic cleaners such as these will etch the surface and attack the metal frame. • Bath and sink cleaners may mark the surface. The Ceramic Hob To reduce the amount of cleaning always ensure that the hob and cooking utensils are clean and dry before use. Regular use of cleaner conditioner is recommended for proper care and protection of the hob surface. Apply conditioner before using the hob for the first time. It contains a mild cleaning agent, so that subsequent cleaning applications may clean off soil and apply a protective film at the same time. For stubborn stains or heavy soiling use any of the following materials, and finish off with conditioner: 1. Cif, non-scratch scouring cream. 2. Liquid Gumption Kitchen Cleanser. 3. Special Powder Cleanser. Stainless Steel Wipe with a cloth wrung out in warm soapy water followed by a wipe with a cloth wrung out in clean water and then dry with a soft clean cloth. Powder Cleanser - Mineral deposits that are present in hard water and some foods may cause discolouration, that appear in the form of grey or brown stains. The stains sometimes appear to be in or under the glass surface. If there are any persistent stains after using any of the other recommended cleaning materials, powder cleanser may be applied, following the manufactures instructions. DO NOT use abrasive cleaners or powder cleanser on the painted metal framework. Pans with aluminium bases should be lifted rather than dragged across the hob surface.This will avoid metal rubbing off the pan onto the glass. Such marks are easily removed by the powder cleanser provided they are not subsequently baked on for long periods at high temperatures. Cleaner Conditioner - Regular use of the conditioner will make the surface easier to clean thus ebsuring that years of heavy abrasive cleaning do not progressively dull the surface. If the hob is scratched through accident or misuse. soil that collects will appear as fine brown lines; these are not fully removable but can be made less obvious by the daily use of cleaner conditioner. Cooking performance is in no way affected by scratched on the surface. Control Knobs Wipe over the knobs with a soft cloth wrung out in warm soapy water or mild non-abrasive.Then, after wiping with a cloth wrung out in clear water, dry with a soft clean cloth. Painted Metal Surround Trim Wipe over with a cloth wrung out in warm soapy water only. DO NOT USE ABRASIVES. Troubleshooting Before calling service for assistance, check through the following list, there may be nothing wrong. Nothing works. Check to make sure that: • the mains wall switch is switched on. If a control is on, the corresponding residual heat indicator light will come on. Hotplates are slow to boil or will not simmer. Check to make sure that: • Your pans conform with the recommendations detailed in this book. If, despite all of these checks, the hob does not function properly and problem persists, call Hotpoint Service (see KEY CONTACTS, back page), informing them of: -The type of problem. -The abbreviation used to identify the model (Mod. ...) as indicated on the warranty. IMPORTANT: Never call upon technicians not authorized by the manufacturer, and refuse to accept spare parts that are not original. 9 Installation These instructions are intended for the qualified technician The four securing springs are held in place by 4 Torx screws. installing the appliance in order to insure that the installation, To remove the hob unit from its housing, undo the 2 Torx adjustments and maintenance procedures are performed screws at the front, then the 2 Torx screws at the rear. correctly and comply with the regulations currently in effect. The 4 screws should be accessible at all times for this Important: the hob must be disconnected from the purpose. power supply before making any adjustments or performing any maintenance, etc. Installing built-in hobs The hob has a type X protection rating against overheating in compliance with regulation CEI 335-2-6.Therefore, the hob cannot be installed alongside of cabinets which are higher than the surface of the hob itself. The following precautionary measures should be observed in order to ensure proper installation: a) Hoods must be installed in compliance with the required specifications contained in the instruction manual for the hood itself. b) The built-in ceramic glass top can be installed on any counter top as long as it is 600 mm or more in width and resistant to temperatures of up to 100°C. The dimensions and the position of the hole are shown in fig.. 560 +/- 1 490 +/- 1 48 595 510 10 Distance to keep between the cut-out slot and the cabinet FRONT RIGHT MOUNTING FRONT LEFT MOUNTING SEAL MOUNTING FRONT / REAR RIGHT / LEFT MOUSSE 5x8 mm HOB UNIT FAST DOWN REAR RIGHT MOUNTING WORK SURFACE REAR SPRING ASSEMBLY FRONT OF THE HOB UNIT 3040 REAR LEFT MOUNTING c) If a wooden panel is installed beneath the hob for insulation purposes, it must...


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien