Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This new carefully de-signed product, manu-factured with the highest quality materials, has been carefully tested to satisfy all your cooking demands.We would therefore request you to read and follow these easy instructions which will allow you to obtain ex-cellent results right from the start. May we wish you all the very best with your modern appliance! THE MANUFACTURER Instructions for use GB Installation All operations relative to installation (electric connection) should be carried out by skilled personnel in conformity with the rules in force. As for the specific instructions see part pertaining to installer. Use Electric plates (Fig. 1 - 2 - 3) Rotate the knob to the position correspondent to the needs of cooking taking into consideration that to a higher number a higher heat supply corresponds, see table “use of electric plates”. “Quick and normal plates”: clockwise and anticlockwise rotation with 7 fixed position (0.6). The pilot lamp on indicates when plate is connected. Some types of pilot lights will maintain some slight luminescence even after disconnection. That is quite normal. N.B.: -When one makes use of electric plates, we advise receptacles with flat bottom having same diameter or lightly higher than that of the plate; -avoid overflows of liquid, therefore when boiling has happened or in any case when liquid is heated, reduce the heat supply; -don’t leave the electrical plates on without receptacles on the top or with void pots and pans; -at the end of cooking take again the knob to position “0”. Maintemace Before every operation it’s necessary to disconnect the apparatus. To obtain a higher life of the apparatus concerned it’s indispensable to carry out at regular intervals a carefully general cleaning bearing in mind the following: -the s/s and/or enameled parts should be cleaned by means of suitable not abrasive or corrosive products (available on the market). Avoid cloride-base products (bleach, etc.) -avoid leaving on the top acid or alkaline substances (vinegar, salt, lemon-juice, etc.) -the electric plates have to be cleaned by means of a wet rag and lightly oiled with lubricant when they are still tepid. DO NOT USE STEAM CLEANERS USE OF ELECTRICAL PLATES quick-normal intensity of heat 1 Weak 2 Gentle 3 Slow 4 Medium 5 Strong 6 Bright Fig.1 Fig.2 Fig. 4 1 - O 145 2 - O 180 Fig. 3 GB Apparatus class I (type Y): it can be brought near furniture being higher than the work-top HO5RR - F3 x 1.5 HO5RR - F4 x 0.75 Fig. 5 ELECTRIC PLATES SUPPLY TYPE W REGULATION ~ 230 V • QUIck O 145 1500 cLOckWISE AND ANTIcLOckWISE ROTATION • QUIck O 180 2000 • red point Instructions for the installer GB Installation These instructions are turned to the skilled installer as a guide toinstallation, regulationand maintenance in compliance with the lawsand the rules in force. Any of these operationsmust always be carriedout when the appliancehas system. been disconnected from the electric Positioning (Fig. 4) The apparatus isprovided to be built-in awork-top as shown in thespecial figure.Present the sealing agentalong all the perimeter. Electrical connection (Fig. 5) Before carrying out theelectrical connection be sure that: -the characteristics of the system are such as tosatisfy what indicated onthe part number plateapplied to the bottom ofthe work-top; -that the system is provided with the effective ground in compliance with the rules and the provisions of law in force. The ground is binding according to the law. In case the apparatus isn’tprovided with cable and/or with relative plugmake use of material suitable for the absorption indicated inthe part number plate andfor the workingtemperature. The cableshould reach in no point atemperature higher 50°cthan of the room temperature. If connecting directly to the mains power supply, fit a multi- poles witch of a suitable size for the rated capacity with a clearance distance which completely disconnects the power line under over voltage category III conditions, consistently with the rules of installation (the yellow/green earth wire must not be interrupted). The plug on the omnipolarswitch should be easilyreachable with apparatusinstalled. N.B.:-The manufacturer declines all responsibilityin case the above and the usual safety rules aren’trespected. To avoid all risk, if the powercable becomes damaged, it mustonly be replaced bythe manufacturer, byan authorised service centre, or by aqualified electrician. 6 Assistance Before contacting After-Sales Service: 1. See if you can solve the problem yourself. 2. Switch the appliance on again to see if the problem has been solved. if it has not, disconnect the appliance from the power supply and wait for about an hour before switching on again. 3. If the problem persists after this course of action, contact After-Sales Service. Specify: • the nature of the fault, • the model • the service number (the number after the word SERVIcE on the rating plate on the rear of the appliance) • your full address, • your telephone...