Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Attention: Do not store flammable material in the oven, or the storage compartment. 26 Removal of the Inner Glass Door Panel – The inner glass door panel can easily be removed for cleaning by unscrewing the four screws (fig. 25). – When re-assembly ensure that the inner glass is correctly positioned and do not over tighten the screws. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass. Fig. 25 Fig. 26 Storage Compartment – The storage compartment is accessible through the pivoting panel. Attention: Do not store flammable material in the oven, or the storage compartment. 27 27 Inside of Oven The oven should always be cleaned after use when it has cooled down. The cavity should be cleaned using a mild detergent solution and warm water. Suitable proprietary chemical cleaners may be used after first consulting with the manufacturers recommendations and testing a small sample of the oven cavity. Abrasive cleaning agents or scouring pads/cloths should not be used on the cavity surface. NOTE: The manufacturers of this appliance will accept no responsibility for damage caused by chemical or abrasive cleaning. Let the oven cool down and pay special attention no to touch the hot heating elements inside the oven cavity. Assembling and Dismantling of the Side Runner Frames – Fit the side runner frames into the holes on the side walls inside the oven (Fig. 27). – Slide the tray and rack into the runners (Fig. 28). The rack must be fitted so that the safety catch, which stops it sliding out, faces the inside of the oven. – To dismantle, operate in reverse order. Fig. 27 Fig. 28 28 28 Removing the Oven Door Please operate as follows: – Open the door completely. – The swivel retainers of the rh and lh hinges (fig. 29a) are hooked onto the metal bar above them (fig. 29b). – Lift the oven door slightly. The noch on the bottom of the hinge will disengage (fig. 29c). – Now pull the oven door forwards off the appliance. Release both hinge sections from the slots (fig. 29d). Door Assembly – Grip the door (as indicated in figure 29) and refit it in reverse order of removing procedure. Fig. 29a Fig. 29b Fig. 29c Fig. 29d Fig. 29 29 29 FOR THE INSTALLER Location space containing a bath or a shower. semi commercial or communal environment. cabinet. to avoid ungluing or deformations. standards. The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or The appliance must not be installed in a bed-sitting room of less than 20m3 . The appliance is designed and approved for domestic use only and should not be installed in a commercial, Your product will not be guaranteed if installed in any of the above environments and could affect any third party or public liability insurances you may have. This cooker has class “2/1” overheating protection so that it can be installed next to a – If the cooker is installed adjacent to furniture which is higher than the gas hob cooktop, a gap of at least 200mm must be left between the side of the cooker and the furniture. – The furniture walls adjacent to the cooker must be made of material resistant to heat. – The veneered synthetic material and the glue used must be resistant to a temperature of 90°C in order – Curtains must not be fitted immediately behind appliance or within 500mm of the sides. – It is essential that the cooker is positioned as stated below. – If the cooker is located on a pedestal it is necessary to provide safety measures to prevent falling out. – The cooker must be installed by a qualified technician and in compliance with local safety 650 mm 200 mm 500 mm 450 mm Fig. 30 30 Fitting the Adjustable Feet – The adjustable feet must be fitted to the base of the cooker before use. – Rest the rear of the cooker an a piece of the polystyrene packaging exposing the base for the fitting of the feet. – Fit the 4 legs by screwing them tight into the support base as shown in picture 32. WARNING When raising cooker to upright position always ensure two people carry out this manoeuvre to prevent damage to the adjustable feet (fig. 34). Fig. 33 Assembling the Backguard – Remove the two spacers “A” and the screw “B” from the rear of the cooktop. – Assemble the backguard as shown in figure 31 and fix it by screwing the central screw “B” and the spacers “A”. ABFig. 31 A B Fig. 32 30 Fitting the Adjustable Feet – The adjustable feet must be fitted to the base of the cooker before use. – Rest the rear of the cooker an a piece of the polystyrene packaging exposing the base for the fitting of the feet. – Fit the 4 legs by screwing them tight into the support base as shown in picture 32. WARNING When raising cooker to upright position always ensure two people carry out this manoeuvre to prevent damage to the adjustable feet (fig. 34). Fig. 33 Assembling the Backguard – Remove the two spacers “A” and the screw “B” from the rear of the cooktop. –...