Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: DCS Dateigröße: 856.81 kb Dateiname: 615f1c23-7dca-f014-0581-445dfbfcf4a6.pdf Unterrichtssprache:

If this is not done, the air supply will be correspondingly reduced and the guarantee will be invalid. The distance between the lower surface of the appliance and shelves/drawers must be min. 20 mm. If the appliance is installed with a base shelf underneath, two cutouts must be created in the shelf - one at the front and one at the rear - to provide sufficient ventilation to the electrical components. The cutouts must be min. 10x250 mm. Installation in cupboard WITH oven If the appliance is installed with an oven located below it, there must be no intervening shelf/panel. The distance between the top of the worktop and the top of the oven must be min. 60 mm (thus ensuring that the distance between the top of the oven and the lower surface of the appliance is greater than 20 mm. Cutting Out When mounting this unit: Read the instructions on this page. When mounting the hob together with other units: Read the instructions on the next page. For mounting the hob you need a Philips screwdriver and the 4 clamping fittings supplied with this product (see fig.). Distance to Wall: Minimum 150 mm to flammable material. Minimum 50 mm to nonflamable material. 1. Cut a hole in the table top according to the measures stated. See “Technical data”, “built-in measurement”. 2. Place the unit upside down on a mat. Take care that the top side is not scratched. 3. Mount the clamping fittings in the holes in the side of the base panel (see fig.) 4. Place the unit in the hole and tighten the clamping fittings to the table top using a screwdriver. Clamping fittings Mounted clamping fittings 31 32 Mounting more than one hob Cutting out The measurement of the selected combination is calculated in the following way: Depth: 490 mm Width: 1. Calculate the sum of all units’ width. 2. Subtract 20 mm from the total width. Example: A hob of 720 mm + a downdraft of 180 mm + a gas hob of 360 mm. 1. 720+180+360= 1260 mm 2. Width of the hole: 1260-20=1240 mm Distance to Wall: Min. 150 mm to flammable material. Min. 50 mm to non-flammable material 490 mm Reinforcement beam Distance to wall: Min. 50 mm (non-flammable material) Distance to wall: Min. 150 mm (flammable material) 33 Mounting: When mounting several hobs together you must use a reinforcement beam between each hob as well as the silicone supplied with the hobs (see fig.) 1. Cut a hole of the calculated size in the table top 2. Place the individual hobs upside down on a mat. Take care that the top side is not scratched. 3. Mount the clamping fittings in the holes in the side of the base panels (see fig.) 4. Place the first hob in the hole. 5. Apply silicone to the two corners joining the next hob (see fig.) Use only the silicone supplied with the hobs as this is intended to tolerate the high temperatures of the appliance. 6. Push a reinforcement beam up against the hob. Apply silicone on the reinforcement beam (see fig.) 7. Tighten the clamping fittings to the table top using a screwdriver. 8. Repeat the process for the other hobs. Silicone To optimise joints between the installed hobs, the gap between the ceramic hob may be grouted with silicone: 1. Remove the aluminium panels from the hobs. 2. Apply a stripe of silicone to the gap between the two ceramic hob. Use only the silicone supplied, as it is designed to tolerate the appliance’s high temperature. (Fig. 1) 3. Splash a little soapy water (washing-up liquid) on the silicone stripe 4. Press the rubber block hard against the ceramic hob and pull it slowly from back to front (Fig. 2) 5. Leave the silicone to harden until the next day. 6. Remove surplus silicone coating from the ceramic hob with the razorblade supplied. Be careful not to damage the silicone in the gap. Run tools only 34 along the joint, never across it. 7. Polish the ceramic hob with the supplied cleaning product for ceramic hobs. 1 2 Overview of the outside width of the units 180 mm Downdraft 360 mm Glass ceramic hob with 2 cooking zones Gas hob with 2 burners Induction hob with 2 cooking zones Grill Grill / Fryer Wok 580 mm Glass ceramic hob with 4 cooking zones Gas hob with 4 burners 720 mm Glass ceramic hob with 4 cooking zones Gas hob with 4 burners Induction hob with 4 cooking zones What to do if... If the appliance is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the aookuabce is under guarantee. Problems Remedy The hob doesn’t work............. Check that the hob is switched on. Check the HPFI/HFI relay in the main fuse box. Check the fuses for the hob. The hob gets hot................. The hob may get as hot as 60°C. The fuses are constantly blowing..... Possibly, you have too many electrical appliance in use at one go. If your hob is connected to a 10 Amp fuse group, there is a high risk of overload. The zones make clicking and other noises During use there will be noise...

Herunterladen

Geben Sie zwei Ziffern: