Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung DCS, modell BGC-1236

Hersteller: DCS
Dateigröße: 1.19 mb
Dateiname: 212071RB.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

3. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. 4. If you cannot reach your gas supplier, call the fire department. 5. Installation and service must be performed by a qualified installer, service agency or the gas supplier. WARNING! Do not place items of interest to children on racks or appliance. Children could be seriously injured if they should climb onto or into the appliance to reach these items. WARNING! Do not place combustible material (paper, cloth, plastic, etc.) on the rack. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE. 1 TABLE OF CONTENTS SPECIFICATIONS 3 WALL MOUNT LOW BACKGUARD INSTALLATION 3 WALL MOUNT FULL BACKGUARD INSTALLATION 4-5 2 SPECIFICATIONS 8-3/4 " 12 " B MODEL A B RACK (13-5/8") QTY. RACK (16-5/8") QTY. BGC-1236 35-7/8" 12" -- BGC-3036 35-7/8" 30" -2 BGC-1248 47-7/8" 12" -- BGC-3048 47-7/8" 30" 2 1 A 1-5/16 " B 1-5/16 " A WALL MOUNT LOW BACKGUARD INSTALLATION 1. Locate and level cooktop per installation instructions. 2. After unpacking all backguard system parts, locate the Back Section 1/8” above and centered over the Trim attached to the cooktop.* Secure Back Section to wall with the appropriate fasteners (not supplied)(fig. 01). *After 1/8” is located, slots in back section may be used to adjust spacing between cooktop trim and backguard for a flush fit. 3. Secure Front Section of backguard to Back Section with #8 self-tapping sheet metal screws supplied (fig. 02). Back Section Trim Slots to choose desired spacing between Cooktop Trim and Backguard. 16” 36” for 30”for 36/48” Back Section Front Section # 8 Self-tapping sheet metal screws Fig.01 Fig.02 3 WALL MOUNT FULL BACKGUARD INSTALLATION RECOMMENDED INSTALLATION ORDER: 1) VENT HOOD 2) BACKGUARD SYSTEM 3) COOKTOP 1. Locate and level cooktop per installation instructions. 2. After unpacking all backguard system parts, locate the Back Section 1/8” (see fig. 03) above and centered over the Trim attached to the cooktop.* Secure Back Section to wall with the appropriate fasteners (not supplied) to anchors or wood stud (fig. 03). WARNING: The Back Section must be securely fastened to the wall. Failure to do so could cause damage or personal injury if the Backguard was to pull free from wall when racks are loaded. The maximum weight placed on each rack should be 10 lbs. *After 1/8” is located, slots in back section may be used to adjust spacing between cooktop trim and backguard for a flush fit. 3. Attach rod, end caps and center stanchion to Front Section of backguard with #10 machine screws supplied (fig. 04). 4. Bend wedge-shaped tabs down on top of the front section approximately 3/16”. When mounting the front section, insure that these tabs engage the mating holes in the top of the rear section (see fig. 05, page 5). 5. Secure Front Section of backguard to the Back Section with #8 self-tapping sheet metal screws supplied (fig. 05, page 5). 6. Attach racks to rod (fig. 06, page 5). The maximum weight placed on ea...