Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung AEG, modell 949600686

Hersteller: AEG
Dateigröße: 292.37 kb
Dateiname: 884730en.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

The fryer You can leave the oil in the container from time to time. How often you need to change the oil depends on how often you use the fryer and for what. You should change the oil and clean the frying container when the oil changes colour and/or if the oil begins to smell. . 1. Remove the safety shield from the drain cock. 2. Place a bowl under the drain cock. Make sure the bowl is large enough to hold the oil in the container. 3. Open the drain cock and let the oil run into the bowl. 4. Close the drain cock. The frying container The drain cock must closed. 1. Remove the metal filter and wash it in warm soap water. 2. Pour warm water with washing-up liquid in the container. You can leave the heating element down when cleaning the container. Clean the container with a brush. 3. Place a bowl under the drain cock. Make sure the bowl is large enough to hold the water in the container. 4. Open the drain cock and let the water run into the bowl. 5. Rinse the container in cold water. Remember to place a bowl under the drain cock to catch the rinsing water. Eventually wipe the container with a dry clotts. 6. Close the drain cock and replace the safety shield. Place the metal filter with the curved side upwards over the drain hole in the container. #$ . Element voltage 240 V Electrical connections 240 V, 1 phase, neutral + earth Total power consumption 2300 W This unit is labelled to indicate conformity with the low voltage directive ( 73/23/EEC ) and the EMC directive ( 89/336/EEC ). . The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Fixing Unscrew the fixing brackets just enough so they may be turmed. Fasten the brackets to the worktop with a screw driver. Cut-out measurements One rectangular hole is sawn out for the hob combination chosen. The depth of the cut-out for any unit is: 490 mm Length of hole = sum of all units` externally measured lenght, less 20 mm. Mounting of Reinforcement Beams A reinforcement Beam, with supporting flanges at each end, is included with each two-burner unit. For unit combinations, a reinforcement beam must be used between each unit. It is not necessary to attach the reinforcement beam to the table surface, as it is held in place by a specially designed moulding, which is incorporated in the hob unit.s flanges. . . . . . . %#. & . . %#. & (. * +. . ,* . . If the hob is mounted in a 270 X 490 mm cutout, or if for other reasons there is no room for the side attachments, these should be removed before the hob is set into the table. Set the hob into the table and then raise it enough to expose the screws in the sides. Remove the screws. Mount the attachment fittings so that they interlock with the frame (See illustration). Reinsert the screws in the sides through the oblong hole in the fitting. Set the hob into the table and tighten the attachment fittings. The units externally measured length 145 mm: Cooker hood 290 mm: Two-burner ceramic-top electric hob Two-burner gas hob Grill Fryer Combi grill 580 mm: Four-zone ceramic-top electric hob Four-burner gas hob 725 mm: Four-zone ceramic-top electric hob . The electrical installation must only be made by a certified electrician. The electrical installation must be made according to prevailing regulations for heavy current installations and comply with local public regulations. No attempt must be made to tamper with the electrical parts of the unit. The hob is supplied with a 1,5 metre power cable without plug and is to be connected to an external relay with a contact separation off at least 3mm in each pole. The guarantee is void in the case of faulty installation or if the electrical parts have been tampered with. Connections to the unit: 1 phase - neutral - earth (max. 10A) Type of cable, min. 1,0 mm. HO5 RN F. . . Check to see whether a fuse has blown. Check to see whether the relay is switched off. If the problem is not with the fuse or relay, do not attempt to correct it yourself. Instead, contact our service network - all repairs must be performed by our service personnel. Warranty This unit is warranted against defects in materials and workmanship, when used as intended, for a period of one year from the date of purchase. The warranty covers both parts and service, as well as necessary transportation costs. Keep your proof of purchase. Reservations The warranty does not cover damages which are not due to defects in materials or workmanship. Repair, or attempted repair, by any party other than our authorized service network will invalidate the warranty. The warranty does not cover an unjustified house-call by our service network. Service and spare parts Service ...