Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Indesit, modell KD6G25SWIR

Hersteller: Indesit
Dateigröße: 238.58 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

The cooker must not be installed in a bed-sitting room of less than 20m3. When adjusted for use on Butane (G30) or Propane (G31), the cooker must not be installed in a room or internal space below ground level, e.g. in a basement. PROVISION FOR VENTILATION The room containing the cooker should have an air supply in accordance with BS 5440: Part 2. The room must have an opening window or equivalent; some rooms may also require a permanent vent. If the room has a volume between 5 and 10m3, it will require an air vent of 50cm2 effective area unless it has a door which opens directly to outside. If the room has a volume of less than 5m3, it will require an air vent of 100cm2 effective area. If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be consulted to determine air vent requirements. TECHNICAL DATA Gas connection Pressure test point Gas rate adjustment Aeration adjustment Electrical connection Rp 1/2 (1/2" BSP female) Front left hotplate injector None None Flexible cord fitted with a 3 pin 13 amp plug 230/240V a.c. 50Hz. 13A fuse. G20 at 20mbar G30 at 28-30mbar G31 at 37mbar Burner Heat Input Injector Heat Input Injector Hotplate Front Left 3.0 kW 116 3.0 kW (220g/h) 86 Hotplate Rear Left and Rear Right 2.0 kW 103 2.0 kW (145g/h) 70 Hotplate Front Right 1.1 kW 79 1.0 kW (70g/h) 50 Grill 2.8 kW 129 2.8 kW (200g/h) 85 Main Oven 2.5 kW 115 2.3 kW (165g/h) 72 Top Oven 1.9 kW 100 1.9 kW (135g/h) 65 16 Installation 0 inDesiT SPACE FOR FIXING The cooker can be close fitted below hotplate level. This requires a minimum distance of 600mm between cupboard units of hotplate height. When installing next to a tall cupboard, partition or wall, for a minimum distance of 400mm above hotplate level, allow a side clearance of at least 65mm. The diagram below illustrates the minimum clearance between the cooker and adjacent walls, cupboards etc. The wall behind the cooker, 50mm below and 450mm above, and the width of the cooker, must be a non-combustible material such as ceramic wall tiles. If the cooker is to be fitted close to a corner on the left hand side, ensure that there is a clearance of at least 50mm to allow the main oven door to open fully for when removing oven shelves. UNPACKING THE COOKER Unpack the components from inside the grill and oven. Check that the following parts are present: Grill pan and grid Top oven/grill shelf heat shield Pan supports Main oven shelves (2) Enamelled burner caps (4) Top oven/grill shelf (1) Aluminium burner bodies(4) Literature LEVELLING Four skid feet are fitted which can be adjusted up or down to level the cooker. CONVERSION FOR USE ON BUTANE (G30) OR PROPANE (G31) Each burner requires the injector to be replaced and bypass screws adjusted or replaced as follows: 600 mm Min COOKER HOODS If a cooker hood is to be installed, refer to the cooker hood manufacturers' instructions regarding fixing height. 1. Remove the loose hotplate burner parts. 2. Using a 7mm socket, replace the hotplate injectors as appropriate (see table on previous page). 3. Re-position the loose burner parts. 4. Remove the enamelled baffle at the front of the grill (2 screws). 5. Remove the screw on the right hand side of the burner and gently slide the burner off the injector. 6. Using a 7mm socket, replace the grill injector as appropriate (see table on previous page). 7. Re-assemble the burner and baffle. 8. Inside the top oven, remove the central screw securing the burner retainer. Slide the retainer to the right slightly and lift away. 9. Lift the burner assembly and place on the floor of the oven to the right of the burner opening. 10.Using a 7mm socket, replace the oven injector as appropriate (see table on previous page). 11. Re-assemble the oven burner and retainer. 12.Replace the main oven injector following the same procedure as for the top oven. 13.Carefully pull off the control knobs. 14.Using a narrow flat bladed screwdriver rotate the bypass screws fully clockwise. The main oven thermostat bypass screw is located on the body of the thermostat below the spindle, the top oven thermostat bypass screw is located on the body of the thermostat to the right of the spindle and the hotplate tap bypass screws are located down the centre of the spindle. 15.Re-assemble the control panel parts. 16. Secure the self-adhesive LPG conversion label over the gas details on the data badge. 17 Installation STABILITY CHAIN A hole in the gas inlet valve bracket can be used to engage a stability chain. CONNECTING TO GAS SUPPLY 670 300 \ Connection to the cooker should be made with an approved appliance flexible connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of hose chosen should be such that when the cooker is in situ, the hose does not touch the floor. Those cookers converted to use on LPG should be connected with a hose suitable for LPG and capable of withstandin...