Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Indesit Dateigröße: 419.44 kb Dateiname: Unterrichtssprache:

Instructions for connecting cable to an alternative plug: Important: the wires in the mains lead are coloured in accordance with the following code: Green & Yellow - Earth Blue - Neutral Brown - Live If the colours of the wires in the mains lead do not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked “E” or or coloured Green or Green & Yellow. Connect Brown wire to terminal marked “L” or coloured Red. Connect Blue wire to terminal marked “N” or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse. A 15 amp plug must be protected by a 15 amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt about the electrical supply to your machine, consult a qualified electrician before use. How to connect an alternative plug: The wires in this mains lead are coloured in accordance with the following code: 5 BLUE “NEUTRAL” (“N”) BROWN “LIVE” (“L”) GREEN AND YELLOW “EARTH” (“E”) GREEN & YELLOW 13 amp fuse BROWN CROSS-BAR CORD GRIP BLUE Disposing of the appliance When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above. Adapting the cooker to different types of gas In order to adapt the cooker to a different type of gas with respect to the gas for which it was produced (indicated on the label attached to the lid), follow these steps: a) Replacing the burner nozzles on the hob: • remove the grids and slide the burners from their housings; • unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). • replace all the components by repeating the steps in reverse order. b) Minimum regulation of the hob burners: • turn the tap to minimum; • remove the knob and adjust the regulation screw, which is positioned in or next to the tap pin, until the flame is small but steady. N.B.: in the case of liquid gas, the regulation screw must be screwed in to the bottom. • check that the flame does not turn off when you turn the tap quickly from high to low. c) Regulating the primary air of the burners: The primary air of the burners requires no regulation. Adapting to different types of gas In order to adapt the oven to a different type of gas with respect to the gas for which it was manufactured (indicated on the label), follow these simple steps: a) Replacing the oven burner nozzle . open the oven door fully . pull out the sliding oven bottom . unscrew the burner fastening screws V . remove screw “V” and then the oven burner; . Unscrew the oven burner nozzle using the special socket spanner for the nozzles, or a 7 mm socket spanner, and replace it with a nozzle suited to the new type of gas (see Table 1). Take particular care handling the spark plug wires and the thermocouple pipes. . Replace all the parts, following the steps described above in the reverse order. b) Minimum regulation of the gas oven burner with thermostat: • light the burner as described in the paragraph “the oven knob” of the instruction booklet. • turn the knob to Max for about 10 minutes and then turn the knob to the Min setting; • remove the knob; • regulate the screw positioned outside the thermostat pin until the flame is small but steady. N.B.: in the case of liquid gas, the regulation screw must be screwed in to the bottom. • check that the burner does not turn off when you turn the knob from Max to Min and and when you open and close the oven door quickly. Adapting the gas grill to different types of gas Replacing the nozzle of the grill burner: • remove the screw and then slide out the grill burner “V” (see Fig. E); 6 • unscrew the grill burner nozzle using the special socket spanner for the nozzles (see Fig. F) or better still a 7 mm socket spanner; replace the nozzle with a nozzle for the new type of gas (see table 1). V I Fig. E Fig. F Important On completion of the operation, replace the old rating sticker with one indicating the new type of gas used.This sticker is available from our Service Centres. Note Should the pressure of the gas used be different (or vary) from the recommended pressure, it is necessary to fit a suitable pressure regulator onto the inlet pipe in compliance with current National Regulations relative to “regulators for channelled gas”. 7 Burner and nozzle characteristics Table 1 Liquid Gas Natural Gas Burner Diameter (mm) Thermal Power kW (p.c.s.*) By-Pass 1/100 Nozzle 1/100 Flow* g/h Nozzle 1/100 Flow* l/h Nominal Reduced (mm) (mm) *** ** (mm) Fast (Large)(R) 100 3,00 0,7 41 86 218 214 116 286 Semi Fast (Medium)(S) 75 1,90 0,4 30 70 138 136 106 181 Auxiliary (Small)(A) 55 1,00 0,4 30 50 73 71 79 95 Oven -2,60 1,0 52 78 189 186 119 248 Grill -2,50 --80 182 179 122 238 Supply Pressures Nominal (mbar) Minimum (mbar) Maximum (mbar) 28-30 20 35 37 25 45 20 17 25 * At 15°C and 1013...

Herunterladen

Geben Sie zwei Ziffern: