Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
• If your cabinet interior dimension is between 565-570mm the oven may still be fitted. However, a minor modification to the cabinet will be required to reduce the aperture size down to 560-565 mm, to allow the product to be securely screwed into the cabinet. • The dimensions given provide adequate air circulation around the unit within the cabinet, ensuring compliance with BS EN60-335. • Enquiries regarding the installation of the cooker point, if required, should be made to your Regional Electricity Company to ensure compliance with their regulations. • The appliance socket switch should be outside the cabinet but within 2m of the appliance to make it accessible to switch off the appliance in case of an emergency. • To protect the hands, wear gloves when lifting the oven into its housing. Do not lift the appliance by the handles. Note: House circuit Earth leakage and continuity tests must be carried out before the appliance is connected to the mains supply and rechecked after fitting. Choice of electrical connection • The appliance should be operated using at least 6mm 2 twin core and earth PVC insulated mulit core cable. Please choose from the most appropriate after reading the different methods:- • By connecting the appliance to a cooker point (having a double pole isolating switch with at least 3mm contact separation in all poles) and protected with a fuse or miniature circuit breaker at your mains fuse box. • If you wish to connect an oven and a hob to a cooker point you can. Oven and hob units should be separately connected to a cooker point. Cooker point Oven Hob Note: It is good practice to : • Fit an Earth Leakage Circuit Breaker to your house wiring. • Wire your appliance to the latest IEE regulations. electrolux installation 35 Preparing cabinet for fitting of oven • Make sure that the cabinet is the correct size for the appliance to be fitted. • If the size is between 565-570mm, then the cabinet should be modified so that at the screw fixing points the recommended dimension of at least 560-565mm is maintained. The modification should ideally be localised to ensure that after screw fitment the oven is securely fixed into position. • The cabinet must be stable and level by firmly securing it to the wall or floor. If necessary, make arrangements to ensure the shelf upon which the oven will rest is level. • When the appliance is installed ensure a minimum gap of 2mm is maintained between the trim on the bottom edge of the appliance, and any corresponding door / panel underneath. 36 electrolux installation Recommended cabinet dimensions (in millimetres) 2000 Recomended907 min 300 min 550 min 560 min 570 max 600 min 558 865 888 16865874-879 11 542 5 Cross section through cabinet showing oven positioned Built in installation How to finish unpacking • • Place packed appliance next to the space in which it will be installed. • Remove the appliance packing except for bottom tray, which should be left in position until the appliance is ready to be fitted into its cabinet. • NOTE: It is imperative that the appliance is left in the base to protect both the appliance and the floor. • Ensure the user is given these operating instructions. Important: Switch off at the mains, miniature circuit breaker and if appropriate, remove fuse before • commencing any electrical work. To remove cover of mains terminal From the rear of the appliance, remove mains input terminal cover to gain access to terminal block. • First remove retaining screw with pozidrive screwdriver. electrolux installation 37 Prise cover loose using screwdriver in position (1) then lever off with screwdriver in position (2) at either side. Lift cover and remove screw from cable clamp. Hook clamp under here Cable clamp 38 electrolux installation Connecting to the mains terminal Warning: This appliance must be earthed. • We recommend you use a new length of 6mm 2 twin core and earthed cable to ensure your safety. • Make connection as shown by proceeding as follows:- • Preform wires to the appropriate shape to suit fitting into the mains terminal block. • Strip inner insulation on wires using wirestrippers. • Twist the bared wires using pliers. • Cut bared wires 10mm away from the end of the inner insulation. Where uninsulated Earth wires are used ensure they are suitably sheathed to leave 10mm bare wire to fit into the terminal. • Clamp bare wires into the relevant terminal and check they are held by tugging each one in turn. • Clamp the mains cable securely ensuring 5mm of the outer insulation is inside the terminal block and that the wires are not taut but not so slack as to cause any fouling. See diagram. • Place fuse/miniature circuit breaker in circuit and switch on at mains. Checking electrical connections Correct electrical connection can be confirmed when switching on the appliance as the timer will be flashing. Note: House circuit Earth leakage and continuity tests must be carried out before the appliance is connected to the mains supply and...
Dieses Handbuch ist für folgende Modelle:Kochfelder - EOD43102 (935.3 kb)
Kochfelder - EOD43102 (935.3 kb)
Kochfelder - EOD43102 (935.3 kb)