Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Gaggenau Dateigröße: 398.55 kb Dateiname: 8d487d27-a3f4-4f54-9cb6-d745d39f3260.pdf Unterrichtssprache:

Thoroughly clean the appliance and accessories before using them for the first time. This will eliminate any 'newness’ smells and soiling (see chapter “Cleaning and care”). About use The appliance is intended solely for household use and must not be put to any other uses. Use the appliance to prepare meals only. Do not use the appliance to heat up the room in which it is installed. Do not use the cooking surface to store items. Place a cooking vessel on the corresponding cooking zone before operating it. Do not remove the cooking vessel until you have switched off the hotplate. The size of pots and pans should correspond to the size of the hotplate. This will save you energy and time. Switch off the hob after use. Iridiscent discoloration can be caused by the bases of some pots. These do not interfere with the operation of the glass ceramic hob. Always keep the cooking area dry and clean. The surface can be scratched due to dirt (e.g. sand grains). Never heat food in aluminium or plastic containers as the material can melt and damage your hob. Built-in overheating protection prevents overheating of the appliance and of surrounding kitchen furniture. In the event of malfunction, first check your household fuses. If the power supply is in proper working order, but the appliance is still not functioning, please inform your specialist dealer or your nearest Gaggenau after-sales service. 2. Features Features 1 2 3 4 5 1 SuperQuick cooking zone O 5 3/4 . . (1100 W), converts to roasting zone 5 3/4 . . x9 1/2 . . (2000 W) 2 SuperQuick cooking zone O 7 . . (1500 W), converts to O 9 . . (2400 W) 3 Display panel with indicator light and residual heat display 4 Control knob for front cooking zone 5 Control knob for rear cooking zone Special accessories You can order the following special accessory: VV 400-000 Connecting trim VZ 400-700 Connecting trim with timer VD 400-000 Appliance cover Visual signals Luminous disc Indicator behind the on the control knob cooker lights OFF light constantly slow flashing of indicator light (long OFF, short ON) fast flashing of a luminous disc fast flashing of both control knobs fast flashing of both luminous discs alternately Signification cooking zone ON residual heat display holiday safeguard power cut faulty installation Cause / Remedy appliance is switched OFF normal use The appliance is too hot to be touched safely. The appliance setting has not been changed for over 4 hours. Turn control knobs to 0 and then switch on again if required. After a power cut, the appliance stays switched off for safety reasons. Turn control knobs to 0 and then switch on again if required. Connecting cable between the appliance and the control panel is not plugged in. Check that cable is plugged in firmly. 9 3. Operation Switching on Press down the control knob for the corresponding cooking position and turn it left or right to the required position (1 -12). The luminous disc behind the control knob and the corresponding indicator light on the display panel light up, as long as the corresponding cooking zone is switched on. The cooking zones are electronically controlled during use, in order to maintain a constant heat, the cooking zone switches on and off intermittently. Switching off Fully turn the control knob to the OFF position. The luminous disc goes off. Indicator light / Residual heat display The corresponding indicator light on the display panel lights, as long as the corresponding cooking zone is switched on. After switching off the cooking zone the corresponding indicator light will flash, as long as the cooking zone has not cooled down sufficiently to be touched safely. Switching on Switching off Indicator light / Residual heat display Holiday safeguard (Automatic switch-off) Cooking zone extension The front cooking zone can be extended to a large diameter The rear cooking zone can be converted to an oval cooking zone especially suitable for oval roasters. Activating extension Turn the corresponding control knob to the right to the extension symbol. An audible signal is sounded and the extension is activated. Now turn the control knob further right to the required position (1 -12). Two spots appear on the indicator display while the cooking zone is on. Note: do not use the roaster zone for heating up round pots or pans. Switching off Fully turn the control knob to the OFF position. The luminous disc goes off. After switching off the cooking zone the corresponding indicator light will flash, as long as the cooking zone has not cooled down sufficiently to be touched safely. Note: the extension will not be activated, when switching the cooking zone on again. The appliance is set to automatically switch off a cooking zone 4 hours after the last operation. The luminous disc behind the corresponding control knob flashes. Turn the control knob to 0. Now the cooking zone can be switched on again as normal. 10 Activating extension 4. Energy Saving Tips Pots and saucepans should always be covered ...

Herunterladen

Geben Sie zwei Ziffern: