Stimmen - 6, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
It contains important information concerning the safe operation, installation and maintenance of the appliance. ! Please keep these operating instructions for future reference. Pass them on to any new owners of the appliance. Positioning ! Keep all packaging material out of the reach of children. It may present a choking or suffocation hazard (see Precautions and tips). ! The appliance must be installed by a qualified professional in accordance with the instructions provided. Incorrect installation may cause harm to people and animals or may damage property. Built-in appliance Use a suitable cabinet to ensure that the appliance functions properly. • The supporting surface must be heat-resistant up to a temperature of approximately 100°C. • If the appliance is to be installed above an oven, the oven must be equipped with a forced ventilation cooling system. • Avoid installing the hob above a dishwasher: if this cannot be avoided, place a waterproof separation device between the two appliances. • Depending on the hob you want to install, the cabinet must have the following dimensions (see figure): Ventilation To allow adequate ventilation and to avoid overheating of the surrounding surfaces the hob should be positioned as follows: • At a minimum distance of 40 mm from the back panel. • So that a minimum distance of 20 mm is maintained between the installation cavity and the cabinet underneath. • Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm from the edge of the hob. FRONT SIDE OF HOB UNDERSIDE OF HOB SUPPORTING SURFACE [ oe o . _ '____ _, 2 H Hotpoint ARISTON F i x ing The appliance must be installed on a perfectly level supporting surface. Any deformities caused by improper fixing could affect the features and operation of the hob. The thickness of the supporting surface should be taken into account when choosing the length of the screws for the fixing hooks: • 30 mm thick: 17.5 mm screws • 40 mm thick: 7.5 mm screws Fix the hob as follows: 1. Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob. 2. Place the hob in the cavity, make sure it is in a central position and push down on the whole perimeter until the hob is stuck to the supporting surface. 3. For hobs with raised sides: After inserting the hob into its cavity, insert the 4 fixing hooks (each has its own pin) into the lower edges of the hob, using the long pointed screws to fix them in place, until the glass is stuck to the supporting surface. ! The screws for the alignment springs must remain accessible. ! In order to adhere to safety standards, the appliance must not come into contact with electrical parts once it has been installed. ! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool. Electrical connection Single-phase connection The hob is equipped with a pre-connected electricity supply cable, which is designed for single-phase connection. Connect the wires in accordance with the instructions given in the following table and diagrams: Voltage and mains frequency 230-240V 1+N -220-240V 1+N -50/60 Hz Electrical cable Wire connection —: yellow/green; N: the two blue wires together L: brown and black together Other types of connection If the mains supply corresponds with one of the following: Voltage and mains frequency • 400V - 2+N ~ 50/60 Hz • 220-240V 3 ~ 50/60 Hz • 230-240V 3 ~ 50/60 Hz • 400V - 2+2N ~ 50/60 Hz Separate the wires and connect them in accordance with the instructions given in the following table and diagrams: Voltage and mains frequency Electrical cable Wire connection 400V - 2+N ~ 50/60 Hz 230-240V 3 ~ 220-240V 3 ~ 50/60Hz ~==r: yellow/green; N: the two blue wires together L1: black L2: brown 400V - 2+2N ~ 50/60 Hz ~==r: yellow/green; N1: blue N2: blue L1: black L2: brown ! The electrical connection for the hob and for any built-in oven must be carried out separately, both for safety purposes and to make extracting the oven easier. Terminal board On the lower part of the appliance there is a connection box for the different types of electricity supply (the picture is only an indication and is not an exact representation of the purchased model). If the mains supply corresponds with one of the following: Voltage and mains frequency • 400V 3 - N ~ 50/60 Hz proceed as follows: ! The cable provided is not suitable for the following types of installation. 1. Use a suitable supply cable, H05RR-F or higher, with the right dimensions (cable cross section: 25 mm). 2. To open the terminal board, use a screwdriver as a lever under the side tabs of the cover (see Terminal board picture). 3. Loosen the cable clamp screw and the terminal board screws in accordance with the type of UNDERSIDE OF HOB 3 connection required and position the connection supports as shown in the following tabl...
Dieses Handbuch ist für folgende Modelle:Kochfelder - 7HKRC 640 X RU/HA (722.2 kb)
Kochfelder - 7HKRC 641 D X RU/HA (722.2 kb)