Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Note:The air quality light ring automatically goes on when the appliance is switched on. The appliance automatically starts operating in the AUTO mode. To switch off the appliance, press the on/off button again and unplug the appliance. Note:When the humidity level in the room is very high, it is possible that condensation develops on the air quality sensor. As a result, the AIR QUALITY light on the control panel and the air quality light ring may indicate that the air quality is bad even though the air quality is good. In this case, the auto mode causes the appliance to run at high fan speed.You can solve this by cleaning the air quality sensor. If condensation develops frequently during periods of high humidity, we advise you to use one of the manual speed settings. Fan speed lights/filter replacement lights -The lights on the right-hand side of the control panel have a dual function: they either indicate the fan speed or they indicate that the filters should be replaced or cleaned. -When lights 1 to 3/4 light up continuously, they indicate the current fan speed. -When light 1 flashes, you have to clean the pre-filter. When lights 2 and/or 3/4 flash, you have to replace these filters. If lights 2 and/or 3/4 flash, the REPLACE FILTER light also flashes (see chapter ‘Filter replacement’ for more information). -When lights 2, 3/4 and the REPLACE FILTER light are on continuously, the appliance is locked (see chapter ‘Filter replacement lock’ for more information). Adjusting the air quality sensor sensitivity People with cer tain health problems (e.g. allergies or asthma) have a greater need for healthy air. For this reason, the appliance allows you to 12 English adjust the sensitivity of the air quality sensor. When it is set to a higher sensitivity level, the appliance already star ts cleaning the air at lower pollution levels to make the air even cleaner. There are 3 sensitivity levels: -standard -sensitive -extra sensitive The pollution sensor is set to standard sensitivity.You can adjust the sensitivity of the air quality sensor in the following way: 1 If the appliance is already plugged in, unplug the appliance and wait for a few minutes. 2 Press the AIR QUALITY button and simultaneously put the mains plug in the wall socket. The appliance beeps twice and oneof the fan speed lights flashes toshow the current sensitivity level of the air quality sensor. sensitivity level: Fan speed lightSensitivity level1 extra sensitive 2sensitive 3 standard 3 Press the FANSPEED button to adjust the sensitivity level of the airquality sensor. One of the fan speed lights flashes to show the set sensitivity level of the air quality sensor. 4 Press the on/off button to switch off the appliance. Note:When you change the sensitivity level, the appliance automatically starts operating at the set sensitivity level whenever you switch on the appliance. Auto mode When the appliance is switched on, the built-in air quality sensor automatically measures the ambient air quality. When the auto mode is activated, the appliance selects the most appropriate fan speed for the measured air quality. 1 Press the on/off button to switch on the appliance. English 13 2 Press the AUTO button to activate the auto mode. Note:When the appliance is operating in another mode and you want to activate the auto mode, simply press the AUTO button. The AUTO light goes on. The FAN SPEED light indicates at which fan speed the appliance is operating. Note:When the air quality is very good and the appliance operates at a very low fan speed, the FAN SPEED light for the lowest speed setting does not go on. In this case only the power-on light and the AUTO light are on. Note:The built-in air quality sensor measures the air quality and automatically selects the appropriate speed setting to ensure the best possible air quality in your room. When the air is clean, the appliance stops running.When the air quality deteriorates, the appliance starts running at a low fan speed and noise level so that the energy consumption is minimised. Night mode The appliance works in harmony with its surroundings. In auto mode, the appliance automatically switches to night mode when the room in which it is operating becomes dark. When the room has been dark for 3 minutes, the lights of the appliance go out, the fan speed and noise level are reduced and the energy consumption is minimised. If the room becomes bright again for 5 minutes or longer, the appliance resumes normal operation. In night mode, the automatic control is still active. If the air is clean, the lights and the fan are off. If the air quality deteriorates, the appliance is activated and the lights and the fan come on again. Note:The night mode only works when the appliance is operating in the auto mode. Fan speed If you do not use the auto mode, you can select the desired fan speed yourself. 1 2 Press the on/off button to switch on the appliance. Press the FAN SPEED button one or more times to select the desired fan...