Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Directives en francais et en espagnol compris. LU® CUS SAVE THE ENVIRONMENT RECYCLE APPROPRIATE MATERIALS Patents: 5,037,583; 5,110,511; 5,133,904 Other Patents Pending Printed in U.S.A To order parts and accessories call 1-800 547-3888 586 4110 Rev. 5/04 Important Safeguards READ BEFORE USING YOUR HUMIDIFIER 1) This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit only one way into a polarized 120-volt AC, 15-amp outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. If an extension cord must be used, it should also accept the wide blade plug and meet this electrical rating. 2) Do not place the cord under rugs, in traffic areas, or near heat sources. 3) Do not use the humidifier if the cord is damaged. 4) Always unplug the power cord before filling, cleaning, servicing, or when the unit is not in use to prevent possible electrical shock. 5) Do not place the humidifier near loose drapes, combustible materials, or heat-producing objects. 6) This humidifier is UL listed with Bemis by Essick Air brand evaporative wicks in place. To maintain your UL safety listing, see your service center for all repairs. Use only Bemis by Essick Air brand replacement wicks and chemicals. To order parts, wicks and chemicals call 1-800-547-3888. 7) Regular cleaning is required. Refer to the CARE AND MAINTENANCE section in this manual. Introduction Your Bemis by Essick Air humidifier adds invisible moisture to your home by moving dry inlet air through a saturated wick. As air moves through the wick, the water evaporates into the air, leaving behind in the wick any white dust, minerals or dissolved and suspended solids. Because the water is evaporated, there is no messy mist or spray, and no white dust, just clean and invisible moist air. As the wick traps accumulated minerals from the water, its ability to absorb and evaporate water decreases. We recommend changing the wick at least once a year, preferably disposing of the used wick at the end of the humidifying season and starting with a new one at the beginning of the next humidifying season. In hard water areas, more frequent replacement may be necessary to maintain your humidifier’s efficiency. CAUTION - We recommend using Bemis by Essick Air Bacteria Treatment or a similar strength product, whenever you refill the water reservoir to eliminate bacteria growth. Follow the directions to determine the proper amount to be added to the 6 gallon water reservoir. The evaporative wick does not require the use of chelating agent type water treatments that are intended for use in Rotobelt or Water Wheel type humidifiers. Your humidifier is provided with a 6 gallon water reservoir. The unit is designed to have an output of 8 gallons per 24 hours. When the reservoir has emptied, the refill light will illuminate. The humidifier fan will automatically shut off. For your safety, unplug humidifier every time it is refilled. If any water spills on the motor chassis, wipe dry before plugging in after filling Dry air is drawn into the humidifier through the top and moisturized as it passes through the wick. Then it is fanned out into the room. 1) water reservoir 2) motor chassis 3) evaporative wick 4) dry air intake 5) moist air output Locate your humidifier at least 4" away from an inside wall, near an electrical outlet. Do not position the unit directly in front of a hot air duct or radiator. 1 2 3 4 5 Assembly and Operation 1) Unpack humidifier from carton. 2) Remove all packaging materials. Check to see that you have the following items before discarding packaging: • Evaporative Wick • Caster pack • Lift rod assembly with styrofoam float Installing Casters: 3) This unit comes equipped with four casters for added convenience. To install the casters, lift the chassis off of the cabinet and place it on a flat, hard surface where it will not be bumped. 4) Lift out the evaporative wick frame assembly from the cabinet and set it aside. 5) To prevent damage to the float and lift rod, untwist the lift rod retainer, and remove the lift rod assembly from the humidifier cabinet. Do not attempt to install casters before removing the lift rod assembly. 6) Turn the humidifier cabinet upside down. 7) Install the casters by inserting the caster shaft into the four small holes positioned roughly 2 inches from each corner of the humidifier cabinet. Push the casters into the cabinet as far as they will go. Do not force. Follow this procedure for all four casters. Turn the cabinet right-side up when done. Assembling Humidifier: 8) Replace the float assembly and attached lift rod into the boxed area on the bottom of the inside of the cabinet. Slip lift rod into retainer ring and twist to secure. The lift rod should be able to freely move up and down about 3/8”. The retainer ring should be located between th...