Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Dual function button: “burst of freshness” 8. Flap to cord storage compartment or “precision steam jet“ 9. Iron rest plate 2. Function selection slide: “burst of freshness” 10. Boiler screw cap or “precision steam jet“ 11. Connection cord to the boiler unit / 3. Diffusion nozzle: “burst of freshness” water tank or “precision steam jet“ 12. Base unit power cord 4. Housing drawer for the removable “burst of 13. Positioning button for the cord guide freshness” capsule (use or storage) 5. Steam control button 14. Control panel 6. Temperature control dial for iron soleplate 15. Boiler unit / water tank 7. Iron temperature control light 16. Cord guide CONTROL PANEL Illuminated On/Off switch Steam indicator Steam output control dial 2 • PREPARING YOUR STEAM GENERATOR Fill the boiler : 1. Place your steam generator on a stable, horizontal heat-resistant surface. 2. Ensure that your appliance is disconnected and cold. 3. Unscrew the boiler screw cap. 4. Using a water jug, fill with one litre of water. 5. Fill the boiler, taking care that the water does not spill over (1). If this occurs, remove the excess water. 6. Replace the boiler screw cap, screwing on tightly. (1) GB The water to use in your steam generator : Your steam generator has been designed to operate using untreated tap water. However, if your water is very hard, mix it 50 % untreated tap water 50 % distilled or demineralised water. Types of water not to use : Heat concentrates the elements contained in water during evaporation. The types of water listed below may contain organic waste, mineral or chemical elements that can cause spitting, brown staining, or premature wear of the appliance : water from clothes dryers, scented or softened water, water from refigerators, batteries, air conditioners, rain water, boiled, filtered or bottled water. Also only use distilled or demineralised water as advised above. 3 • INSERTING THE REMOVABLE “BURST OF FRESHNESS” CARTRIDGE 2 removable “burst of freshness” cartridges are provided in the product packaging. Inserting the cartridge: 1. Open the cartridge housing drawer by pulling it out horizontally (2) 2. Remove the cartridge closing stopper (3). 3. Insert the cartridge in its housing, pressing down firmly (an audible “click” indicates that the cartridge has been inserted correctly) (4). 4. Close the drawer again by pushing it in horizontally (an audible “click” indicates that the drawer has been closed correctly) (5). (2) CLICK CLICK (3) (4) (5) 4 • USING YOUR STEAM GENERATOR 1. Open the flap to the cord storage compartment by undoing the catch. 2. Completely remove the cords from the storage compartment and slot them into the notches on either side of the flap (6). 3. Close the door. 4. Connect your steam generator to a socket with an earth connection. 5. Press on the illuminated on/off switch. (6) The steam indicator lights up while the boiler is heating up. When the indicator goes out (after about 7 minutes), steam is ready (7). 6. Fit the cord guide onto the positioning button situated on the side of the base unit. 7. Fit the steam cord over the loop (8). You can use your appliance and start ironing. During ironing, the temperature control light located on the iron and the steam indicator will go on and off according to (7) the temperature control. GB (8) Be careful: The first time the appliance is used, there may be some fumes and smell but this is not harmful. They will not affect use and will disappear rapidly. 5 • STEAM IRONING 1. Place the iron’s temperature control to the setting suitable for the type of fabric to be ironed (9). •Synthetics (Low temperature) •• Silk/Wool (Medium temperature) ••• Cotton/Linen (High temperature) With delicate fabrics (•setting), press the steam (9) control button (under the handle of the iron) intermittently to avoid water droplets appearing with the steam. 2.The iron temperature control light turns on. Be careful: the generator and the iron are ready to use when both the iron’s thermostat light and the “steam ready” indicator go out. If necessary, also adjust the steam output (steam output control dial on the control panel) (10), eg : less steam for low temperatures. 3. To obtain steam, press on the steam control button beneath the iron handle and keep it pressed (11). The steam will stop when you release the button. Note: It is normal for the connection cord to become warm during use. (10) (11) cotton-linen silk- wool synthetics MIN SETTING THE TEMPERATURE CONTROL AND STEAM OUTPUT CONTROL DIAL ACCORDING TOTHE TYPE OF FABRIC TO BE IRONED : GB Type of f abr ic Set ting t emper at ur e contr ol Set ting st eam output contr ol dial S ynthetics cotton-linen silk- wool synthetics MIN • (L ow temperature) Silk / W ool cotton-linen silk-wool synthetics MIN •• (Med i um temperature) Cot t on / Linen cotton-linen silk- wool synthetics MIN ••• (H i gh temperature) Recommendations: To prime the steam circuit, either before using the iron for the first time, or if you have not used ...