Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
2 Lift up the filler cap › and pour water through the hole into the water tank ‚, using the beaker provided E A. 350ml of water fills the tank. After filling, replace the fill cap. In hard water areas, the use of distilled or demineralised water is recommended. WARNING: Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refrigerator. 3 Always pour out the remaining water after use. WARNING: When filling your iron with tap water, always use the beaker provided. Never fill directly under the tap. fl ‡ · ‚ ‰ 400 350 300 A ‹ ¤ . › fi E „ A UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 40692 rev2 20/6/08 14:32 Page 4 5 Temperature control B • Default setting + 3 dot (cotton). • To increase the temperature, press the arrow !. • To decrease the temperature, press the arrow ". • The temperature console · will flash to indicate that the iron has not yet reached the correct temperature. • Once the correct temperature has been reached, the light will stop flashing and there will be one ‘beep’ to signal that the iron is now ready for use. FEATURES OF YOUR IRON Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control ‹ is set to the ‘0’ symbol. Any temperature setting may be used depending on the garment. The spray feature may be used, providing there is water in the tank (see filling section). You do not need to put any water in the tank when dry ironing only. Spray C Press the spray button ¤and aim the spray of water at stubborn creases. You can do this whilst dry ironing, providing there is water in the tank. When using the water spray, it may be necessary to push the button a few times to get the spray pump primed. Variable steam D Fill the iron with water, as described in ‘Filling’ on page 4, and insert the plug into the electrical socket. The steam output can be varied from low to high by moving the variable steam control D. The steam facility should only be used on garments which are suitable for ironing at the 3 dot and MAX setting. Shot of steam E Press the shot of steam button .to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set within the steam range. Do not use the shot of steam at temperatures below the steam range shown on the control dial. Note: For optimum steam quality, do not operate the shot more than three times in succession. B Increase temperature Decrease temperature C Steam off ‘MAX’ steam D 5 E 40692 rev2 20/6/08 14:32 Page 5 6 Vertical steam F Hold the iron in a vertical position between 1cm and 2cm away from the item F. Press the shot of steam button ., this will create vertical steam. This feature is especially useful for removing creases from hanging clothes, curtains, wall hangings, etc. Note; For optimum steam quality, do not operate the shot more than three times in succession. No drip system Your iron is fitted with a no drip system which is designed to prevent water escaping from the soleplate when the iron is too cold. During use, the no drip system may emit a loud click, particularly during heat-up or whilst cooling down. This is perfectly normal and indicates that the system is functioning correctly. Auto shut-off Your iron is fitted with the auto shut-off function, it will automatically shut down after a set period. The ‘safety switch off’ LED will flash on the function panel. If the iron is left unattended in the horizontal position, it will shut down after 1 minute. If it is left in the vertical position, it will shut down after 8 minutes. To reactivate the iron, gently shake it and wait for the iron to heat-up as normal. Life long anti-scale system The life long anti-scale system reduces scale deposits and helps prolong the life of the iron. MAINTENANCE Self cleaning G Your iron has a built in cleaning system designed to keep the water valve, steam chamber and steam vents clear of lint and loose mineral deposits. 1 Half fill the iron with water. 2 Place the iron on it’s heel. 3 Connect to a mains supply outlet. 4 Set the temperature control to ‘MAX’. See ‘Temperature control’ on page 5. 5 The indicator LED will flash until the required temperature is reached. 6 The indicator LED remains ‘on’ when the selected temperature is attained. 7 Disconnect the iron from the mains supply outlet. 8 Hold the iron horizontally over a sink. 9 Press and hold down the Self-clean button ‡ G. 10 Steam and boiling hot water will drain from the holes in the soleplate, washing away the scale and minerals that have built up inside the Steam Chamber. 11 Gently move the iron back and forth until the water tank is empty. 12 When cleaning is complete, release the Self-clean button ‡. 13 Rest your steam iron back on it’s heel and allow to fully cool down. 14 Wipe the soleplate with a cold, damp cloth. Af...