Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Verify that light on switch is illuminated. 3. Hold Steam Nozzle over object that you desire to steam. Press Steam Trigger. Steam should begin flowing from Steam Nozzle in approximately 45 seconds. 4. When finished using QuickSteamTM Professional, set Lighted On/Off Switch to the “Off” position. NOTE: It is normal for steam to flow from the Steam Nozzle for a period of time after the unit is turned off. This occurs because the Steam Trigger allows water to flow into the unit’s boiler. Once you release the Steam Trigger, the remaining water in the boiler will continue to flow from the Steam Nozzle for a period of time until the boiler is empty. AUTO SHUT-OFF The QuickSteamTM Professional is equipped with an Auto Shut-Off feature. This protects the unit from damage that can occur from operating with a dry Water Tank. If the water level inside the Water Tank drops below the Water Fill Line (which can be found inside the Water Tank), the unit will automatically shut down and cannot be restarted until water is added and level exceeds the Water Fill Line. 10 USING YOUR QUICKSTEAMTM PROFESSIONAL STEAMING FABRIC CAUTION: Be careful when handling garments on Clothes Hanger Hook. Pulling on the garment with too much force may cause unit to tip over. 1. To steam garment, place it on clean, rust-free clothes hanger, and place hanger on Clothes Hanger Hook. 2. Grasp Handle, and direct Steam Nozzle at the bottom of garment. Steam will rise along inside and outside of fabric, removing wrinkles. Slowly slide nozzle vertically, from bottom to top of garment. NOTE: DO NOT allow kinks to form in Hose at any time. 3. Direct steam away from garment, and smooth fabric with free hand. 4. Repeat steps 2 and 3 as necessary until fabric is wrinkle-free. 5. Curtains and draperies can be steamed while still hanging. 6. To remove wrinkles from towels, handkerchiefs, and napkins, drape them over a rod or towel rack, and gently steam. 7. Heavier fabrics may require repeated steaming. 8. To remove stubborn wrinkles, steam both sides of fabric. For special steaming needs, a Fabric Brush and Lint Remover have been included with your QuickSteamTM Professional. See the “Attaching Accessories to Steam Nozzle” section on page 9 for more information on attaching these accessories. FABRIC BRUSH LINT REMOVER May be used to assist you in Useful for removing lint and removing exceptionally other small particles from stubborn wrinkles from fabric garments, drapes, and curtains NOTE: Refer to page 3 of this manual for information on acquiring replacement accessories. CARE AND STORAGE GUIDELINES CARE AND STORAGE GUIDELINES QUICK STORAGE 1. Set Lighted On/Off Switch to “Off” position. 2. Unplug Power Cord from electrical outlet. 3. Wrap Hose loosely around Pole one time. 4. Hang Steam Nozzle from Steam Nozzle Holder. 5. Roll QuickSteamTM Professional to a convenient storage location. CLEANING AND LONG-TERM STORAGE It is recommended that you follow this procedure at least once per week. Use of distilled or de-mineralized water reduces the need for cleaning and prolongs the lifetime of your QuickSteamTM Professional. 1. Set Lighted On/Off Switch to “Off” position. 2. Unplug Power Cord from electrical outlet. 3. Wait for unit to cool completely (at least 30 minutes). 4. Remove Hose and Pole from unit, and set them aside. 5. Using Carrying Strap, carry the unit to a sink or tub. 6. Drain water from Water Tank into sink or tub. Rinse Water Tank with fresh water, and drain completely. 7. Drain steamer by removing Drain Plug and emptying the contents into sink or tub. Tilt unit towards Drain Plug to facilitate removal of water. 8. Flush unit by filling Water Tank and Hose Base with fresh water and draining completely. Replace Drain Plug. 9. Reattach Pole and Hose to unit (refer to assembly instructions on pages 8 and 9 for assistance). 10. Wrap Hose loosely around Pole one time. 11. Hand Steam Nozzle from Steam Nozzle Holder. 12. Roll QuickSteamTM Professional to a convenient storage location. REPLACING THE WATER FILTER The QuickSteamTM Professional incorporates a unique replaceable water filter in its steam delivery system. This filter removes most impurities found within water, ensuring that steam produced by the unit is as clean and pure as possible. After a certain amount of use, the filter will no longer remove water impurities as efficiently. When this occurs, it is recommended that you replace it in order to continue getting the most out of your QuickSteamTM Professional. To do this, simply unscrew the Drain Plug Cap, grasp the filter by the handle, and pull it out. Then insert a new filter into the unit cylinder-first (refer to item 15 on page 6 for an illustration of correct filter orientation). See order form on page 3 of this manual for information on obtaining new water filters. REMOVING MINERAL BUILDUP One common problem with steamers is mineral build-up caused by a high mineral content in many municipal water supplies. Mineral residue inside of i...
Dieses Handbuch ist für folgende Modelle:Bügeleisen - SF-465 (442.45 kb)