Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
2 ) To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3 ) The iron should always be turned to “Off” before plugging or unplugging from the outlet. Never yank cord to disconnect from the outlet; instead, grasp plug and pull to disconnect. 4 ) Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. 5 ) Always disconnect iron from electrical outlet when filling with water or emptying and when not in use. 6 ) Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron, take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. 7 ) Do not allow children to use iron. Close supervision is necessary for any appliance being used near children. Do not leave iron unattended while connected or on an ironing board. 8 ) Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir. 9 ) If the malfunction indicator goes on, the flatiron is not operating normally. Disconnect from the power supply and have the flatiron serviced by qualified service personnel. 10 ) When using vertical steam function, do not point the iron towards yourself or anybody else. SAVE THESE INSTRUCTIONS SPECIAL INSTRUCTIONS 1 ) This is a 1440 watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2 ) If an extension cord is absolutely necessary, a 12 ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. SAVE THESE INSTRUCTIONS Welcome Thank you for purchasing the Oliso Touch&GlideTM iron. You’re just a few steps away from a whole new way of ironing. Follow the instructions in this manual to learn about your new iron’s features and care. We hope you enjoy your Oliso Touch&GlideTM. Plug in, then choose a fabric setting. 3 simple steps to start SET UP Open the Flip FunnelTM and add water to the tank with the fill cup or directly from a faucet. 1 FILL 2 When the blinking green light becomes IRON 3 When the blinking green light becomes IRON 3 Enjoy your Touch&GlideTM! If you would like to learn more about your iron’s unique features, please read on. steady, touch the handle and iron. status light steam button spray button steam selector electronic fabric selector knob drain spout spray nozzle Flow GlideTM soleplate Auto-LiftTM spacers Smart TouchTM handle Auto-LiftTM override switch Flip FunnelTM water tank iron getting to know your status light steam button spray button steam selector electronic fabric selector knob drain spout spray nozzle Flow GlideTM soleplate Auto-LiftTM spacers Smart TouchTM handle Auto-LiftTM override switch Flip FunnelTM water tank iron getting to know your TM Auto-Lift system To operate, place the iron on its soleplate on a flat surface. Plug the iron into an outlet and make sure the Auto-LiftTM switch is in the on ( ) position. Simply touch the iron handle and the iron will sense your hand and lower. Any time you release the handle the spacers will automatically raise the iron to protect your fabric. overriding the Auto-LiftTM systemIf you wish to turn off the Auto-LiftTM system, move the switch on the back of the iron to the off ( ) position. Your Touch&GlideTM will now operate like a standard iron. If the iron is left in the horizontal position for more than 30 seconds, the Auto-LiftTM spacers will raise. This will prevent the iron from burning your fabric or ironing surface. Touch the iron handle and the iron will lower. You can restore Auto-LiftTM by returning the switch to the on ( ) position. water tank Open the Flip FunnelTM. If you need to add water during ironing, unplug the iron and repeat the above steps. After filling, make sure the iron is fully reheated before ironing. Alternatively, fill directly from a faucet holding the iron horizontally. Do not fill the tank past the MAX fill line on the side of the iron. Close the port when done. Leave the iron in a horizontal position and fill using the included fill cup. Two fill cups equal the maximum capacity of the water tank. This iron is designed to be used with regular tap water. If your water is over 12 grams of hardness we recommend using either inexpensive bottled spring water or mixing half tap water with half distilled water. Never use 100% distilled water as this can cause the iron to spit and leak. water recommendations Before filling, slide the steam selector to off ( ). Make sure the iron is unplugged. fabric selector fabric selector knob temperature is too low for steam steam ok Turn the grey fabric selector knob to select a fabric setting. To use constant steam or steam burst, the temperature must be set to the cott...