Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Always disconnect iron from electrical outlet when filling removable water reser voir with water or emptying and when not in use. Be careful to avoid spilling water o ver the iron when filling reservoir. Do not place or store iron where it can fall or be pulled into a tub or sink. To protect against a risk of electrical shock, do not immerse the iron in water or other liquids. Close supervision is necessary for any appliance being used by or near children or invalids. Do not leave iron unattended while connected or on an ironing board. Always position iron carefully to prevent it from falling off or being knocked off ironing board, or if cord is pulled. When not in ironing p o s i t i o n ,a lw ays stand iron on heel re s t . Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Philips Electronics North America Corporation. Do not operate this appliance if it has a damaged iron is used. 1. 2. 3. 4. 5. 6. cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. To avoid the risk of electric shock, do not disassemble the iron; return the iron to the retail location where it was purchased for examination and repair. Incorrect reassembly can cause a risk of electric shock when the 7. Do not allow cord to touch hot surfaces. Let the iron cool completely before putting away. Loop cord around cord wrap when storing. 8. When not in use, the Temperature Control should always be turned to Min position. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect. 9. Do not use outdoors or operate where oxygen is being administered or in the presence of explosive and/or flammable fumes. 10. Burns can occur from hot metal parts, hot water or steam. Use caution when you turn a steam iron upside d ow n - - t h e re may be hot water in the internal re s e rvo i r. 11. The iron may be cleaned by wiping with a damp cloth. Always unplug cord from outlet and allow iron to cool before cleaning. 12. This appliance is intended for household use ONLY; it is not for commercial use or industrial use. 13. For any service issues contact the retail location where product was purchased. 14. IRON MAY BE USED ONLY WITH ALTERNATING CURRENT (AC). NEVER PLUG IRON INTO A DIRECT CURRENT (DC) OUTLET. Table of Contents Table of Contents HI478/IRON.FA 1/13/00 2:35 PM Page 4 SPECIAL INSTRUCTIONS 1. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, a 10-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. SAVE THESE INSTRUCTIONS SPECIAL POLARIZED PLUG INSTRUCTIONS This Philips Iron has a polarized plug for an added safety feature. • Plug will fit into polarized outlet only one way. • If plug does not properly fit outlet at first, reverse it. • If plug still does not fit, contact a qualified electrician. DO NOT ATTEMPT TO DEFEAT THIS SAFETY FEATURE Features 2 Before Using 3 For Dry Ironing 3 Filling the Removable 3-4 Water Reservoir Setting the Temperature 4 Steam Ironing 5 Other Features 5-6 Self-Cleaning 6-7 Maintenance and Storage 7-8 Temperature and Fabric Guide 9 Problems 10 For Assistance 10 Warranty Back Cover HI478/IRON.FA 1/13/00 2:35 PM Page 6 2 3 Before Using Features Spray Button Shot Of Steam Button Dual Language Amber Temperature Pilot Light Control Dial Red Auto-Off Removable Pilot Light Water Reservoir Release Buttons Variable Steam Fabric Control Guide Anti-Calc Full Length Filter Button Groove Removable Water Button Self Clean Reservoir • Drip Stop System Polished Optinox Soleplate Automatically shuts off water with Special 39-Vent Bell Pattern supply if iron is to cool to steam. ensures optimal and even steam d i s t r i b u t i o n IMPORTANT: When using your iron for the first time, you may notice a white deposit coming from the iron as it heats up.This is simply a residue left over from the final buffing of the iron soleplate. Follow the steps in “Before Using” to remove this residue. Remove any sticker or protective foil from soleplate To ensure maximum steam performance, •Clean any left over residue from the Steam Vents by following this procedure: 1 2 3 4 5 6 7 8 9 Turn Steam Control to position 0. Fill iron (see section Filling the Removable Water Reservoir). Plug cord into electrical outlet. Set Temperature Control to maximum setting and allow iron to heat up for approximately 2 minutes. Turn Steam Control to position 3-4. Hold iron over ironing board and allow to steam for 1 minute, dislodging any residue. Iron over an old cotton towel (or other disposable non- synthetic cloth) for several minutes. Turn Steam Control to position 0 and Temperature Control to Min setting. Let iron cool. Clean Steam Vents. Iron is ready to use. Iron is ready for use.For Dry Ironing 1 2 3 4 Plug cord into 120V AC o...