Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 1.49 mb Dateiname: Unterrichtssprache:

Caution -If the appliance has an ear thed plug, it must be plugged into an ear thed wall socket. -Check the mains cord regularly for possible damage. -The soleplate of the iron can become extremely hot and may cause burns if touched. -When you have finished ironing, when you clean the appliance, when you fill or empty the water tank and also when you leave the iron even for a shor t while: set the steam control to position O, put the iron on its heel and remove the mains plug from the wall socket. -Always place and use the iron on a stable, level and horizontal surface. -Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank. -This appliance is intended for household use only. Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user Do not put perfume, vinegar, starch, descaling agents, ironing aids, chemically descaled water or other chemicals in the water tank. 1 2 3 4 Switch off the appliance and unplug it. Set the steam control to position O (= no steam) (Fig. 2). Open the cap of the filling opening. Tilt the iron and fill the water tank up to maximum level under the tap (Fig. 3). Note: Do not fill the water tank beyond the MAX indication. Note: If the tap water in your area is very hard, we advise you to use distilled water. Do not use chemically descaled water. 5 Close the cap of the filling opening (‘click’). Setting the temperature 1 2 Put the iron on its heel (Fig. 4). To set the required ironing temperature, turn the temperature dial to the appropriate position. Check the laundr y care label for the required ironing temperature. -1 Synthetic fabrics (e.g. acr ylic, viscose, polyamide, polyester) -1 Silk -2Wool -3 Cotton, linen If you do not know what kind or kinds of fabric an ar ticle is made of, determine the right ironing temperature by ironing a par t that is not visible when you wear or use the ar ticle. Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches. Avoid using the spray function to prevent stains. Star t ironing the ar ticles that require the lowest ironing temperature, such as those made of synthetic fibres. 3 Plug in the appliance. If the appliance has an earthed plug, put the mains plug in an earthed wall socket. The temperature light goes on. ,4 When the temperature light goes out, wait a while before you start ironing. During ironing, the temperature light goes on from , time to time. This indicates that the iron is heating up to the set temperature. Using the appliance Note:The iron may give off some smoke when you use it for the first time.This stops after a short while. Steam ironing 1 2 3 Make sure that there is enough water in the water tank. Set the recommended ironing temperature (see chapter ‘Preparing for use’, section ‘Setting the temperature’). Set the appropriate steam setting. Make sure that the steam setting is suitable for the ironing temperature selected: (Fig. 2) - for minimum steam (temperature settings 2 and c 3). -e for maximum steam (temperature settings 3 to MAX). Note:The iron starts to produce steam as soon as it has reached the set temperature. You can use the spray function at any temperature to moisten the ar ticle to be ironed.This helps remove stubborn creases. 1 2 Make sure that there is enough water in the water tank. Press the spray button several times to moisten the article to be ironed (Fig. 5). Shot of steam (specific types only) A powerful shot of steam helps to remove ver y stubborn creases. The shot-of-steam function only works at temperature settings between 2 and MAX. 1 Press and release the shot-of-steam button (Fig. 6). Vertical shot of steam (specific types only) You can also use the shot-of-steam function when you hold the iron in ver tical position.This is useful for removing creases from hanging clothes, cur tains etc. 1 Hold the iron in vertical position and press and release the shot-of-steam button (Fig. 7). Never direct the steam at people. Drip stop (specific types only) This iron is equipped with a drip-stop function: the iron automatically stops producing steam when the temperature is too low to prevent water from dripping out of the soleplate. When this happens you hear a click. Automatic shut-off function (specific types only) The automatic shut-off function automatically switches off the iron if it has not been moved for a while. The automatic shut-off light flashes to indicate that , the iron has been switched off by the automatic shut-off function. (Fig. 8) To let the iron heat up again: 1 Pick up the iron or move it slightly. The automatic shut-off light goes out. , If the temperature of the soleplate has dropped , below the set ironing temperature, the temperature light goes on. 2 If the temperature light goes on after you have moved the iron, wait for it to go out before you start ironing. Note:...

Herunterladen

Geben Sie zwei Ziffern: