Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 5.46 mb Dateiname: Unterrichtssprache:

You are not pressing the steam trigger. There is not enough water in the steam tank. Superheated (i.e. high-quality) steam is hardly visible, especially when the temperature dial is set to maximum position and even less so when the ambient temperature is relatively high. Impurities or chemicals present in the water have deposited on the soleplate. This phenomenon ceases after a shor t while. These par ticles are harmless and stop coming out of the soleplate after you have used the iron a few times. Set an ironing temperature that is suitable for steam ironing (temperature settings 2 to MAX). Set the on/off switch to ‘I’. Put the steam tank on a stable and even surface. This is normal. Hold the iron over an old cloth and press the steam trigger.The cloth absorbs the drops. After a few seconds, the steam production becomes normal. Set the on/off switch to ‘I’ Wait 6 minutes for the steam tank to heat up. Press the steam trigger and keep it pressed while you steam iron. Fill the steam tank. See chapter ‘Preparing for use - Filling the Steam tank’. To check if the iron really produces steam, hold a (cold) mirror in front of the soleplate vents. Clean the soleplate with a damp cloth. EnGlISh 13 ProblemCauseSolution Steam escapes from the filling hole area during ironing. Wet spots appear on the garment during ironing I cannot put the iron on its heel. You have been ironing at too high Clean the soleplate with a damp temperatures. cloth. Set the iron to the required ironing temperature (see chapter ‘Preparing for use’, section ‘Setting the temperature’). You may not have tightened the steam Switch off the appliance and let it tank cap properly or you have spilled cool down. Remove the steam tank some water around the filling hole cap, wipe away the water round the filling hole and tighten the steam tank cap again.Then switch on the appliance again. The wet spots that appear on your garment after you have steam ironed for some time may be caused by steam that has condensed onto the ironing board. Iron the wet spots without steam for some time to dr y them. If the underside of the ironing board is wet, wipe it dr y with a piece of dr y cloth. To prevent steam from condensing onto the ironing board, use an ironing board with a wire mesh top. This iron has been designed in such a Place the iron on the heat-resistant way that it can only be placed iron resting mat. horizontally. 14 Pendahuluan IndonESIa 14 Pendahuluan IndonESIa Selamat atas pembelian Anda dan selamat datang di Philips! Untuk memanfaatkan sepenuhnya dukungan yang ditawarkan Philips, daftarkan produk Anda di Tiga langkah untuk menyetrika yang ergonomis 1 Tinggi meja ergonomis (Gbr. 1) Atur meja setrika Anda pada ketinggian yang tepat. Bila Anda berdiri jarak antara siku Anda dan meja setrika kurang-lebih 27 cm. Anda dapat menggunakan alas meletakkan setrika tahan panas sebagai panduan. 2 Desain setrika ergonomis (Gbr. 2) Pegangan yang miring ke atas memastikan posisi yang nyaman pada pergelangan. 3 Alas meletakkan setrika ergonomis (Gbr. 3) Alas meletakkan setrika memungkinkan Anda meletakkan setrika secara mendatar pada meja setrika. Hanya gunakan alas setrika di atas meja setrika - jangan sekali-kali menggunakannya pada permukaan yang tidak tahan panas (Gbr. 4). Jangan letakkan setrika yang masih menyala pada...

Herunterladen

Geben Sie zwei Ziffern: