Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 4.52 mb Dateiname: Unterrichtssprache:

If there is no Consumer Care Centre in your countr y, go to your local Philips dealer. troubleshooting This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, contact the Consumer Care Centre in your countr y. Problem Possible cause Solution The appliance is not switched on. Set the power knob with steam control to a steam setting. The appliance does There is a connection problem. Check the mains cord, the plug not become hot. and the wall socket. 12 EnGlISh Problem Possible cause Solution The set ironing temperature is too low. Set a higher ironing temperature. Some smoke comes out of the appliance after I have switched it on for the first time. This is normal. Some par ts of the appliance have been greased lightly in the factor y. This phenomenon ceases after a shor t while. The appliance produces a pumping sound. Water is pumped into the boiler inside the steam generator.This is normal If the pumping sound continues non-stop, switch off the appliance immediately and unplug it. Contact an authorised Philips ser vice centre. The appliance does not produce any steam. There is not enough water in the water tank. Fill the water tank. The steam generator is not hot enough to produce steam. Wait until the steam setting light stays on. You are not pressing the steam trigger. Press the steam trigger and keep it pressed while you steam iron. The water tank is not placed properly in the appliance. Slide the water tank firmly back into the steam generator (‘click’). Superheated (i.e. high-quality) steam is hardly visible, especially when the temperature dial is set to maximum position and even less so when the ambient temperature is relatively high. To check if the iron really produces steam, set the iron to a lower temperature setting between 2 and 3 for more visible steam. The appliance is not switched on. Set the power knob with steam control to a steam setting. Water droplets come out of the soleplate. When you star t steam ironing and when you continue steam ironing after an interruption, the steam that was still present in the hose has cooled down and condensed into water.This causes water droplets to come out of the soleplate. This is normal. Hold the iron over an old cloth and press the steam trigger. The cloth absorbs the drops. After a few seconds, steam instead of water comes out of the soleplate. The temperature dial is set to a temperature that is too low for steam ironing. Set an ironing temperature that is suitable for steam ironing (temperature settings 2 to MAX). Wet spots appear on the garment during ironing. The wet spots that appear on your garment after you have steam ironed for some time may be caused by steam that has condensed onto the ironing board. Iron the wet spots without steam for some time to dr y them. If the underside of the ironing board is wet, wipe it dr y with a piece of dr y cloth. Water leaks from the appliance. If you tilt the steam generator during transpor t or place it on an uneven surface when the water tank is full, water may spill out of the water tank. Do not tilt the appliance when the water tank is full. EnGlISh 13 Problem Possible cause Solution Water spots appear on the garment during use of the steam boost function. The water spots on your garment are due to condensation in the supply hose. When the supply hose cooled down, the steam that was still present in the hose cooled down and condensed into water. The water droplets stop coming out of the appliance when you have used the steam boost function for some time. Flakes and impurities come out of the soleplate or the soleplate is dir ty. Impurities or chemicals present in the water have deposited in the steam vents and/or on the soleplate. Clean the soleplate with a damp cloth. Too much scale and minerals have accumulated inside the steam generator. Rinse the steam generator frequently (see chapter ‘Cleaning and maintenance’). The steam supply hose is warm during ironing. This is normal as steam passes through the steam supply hose during steam ironing. Place the steam supply hose on the opposite side of the ironing board in such a way that your hand does not touch the hose during ironing. I cannot put the iron on its heel. The iron cannot be put on its heel because it has an ergonomic design that reduces strain on your wrist (see chapter ‘Introduction’). Place the iron horizontally on the heat-resistant iron resting mat. GC8461/GC8460 The cord jammed during rewinding. Pull a small par t of the cord out of only:The cord is not the appliance and press the cord wound completely rewind button again. when I press the cord rewind button 14 Български увод Поздравления за вашата покупка и добре дошли във Philips! За да се възползвате изцяло от предлаганата от Philips поддръжка, регистрирайте продукта си на Две стъпки за ергономично гладене 1 Ергономичен дизайн на ютията Извитата нагоре ръкохватка о...

Herunterladen

Geben Sie zwei Ziffern: