Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
USING THE VERTICAL STEAM FUNCTION The vertical steam features allows you to eliminate wrinkles from drapes without having to take them off the rod or to freshen the appearance of clothing while on the hanger. 1. Unplug the iron from the outlet. 2. Fill the reservoir with water, see FILLING THE WATER RESERVOIR. 3. Position temperature control dial to MAX setting. 4. Stand the iron on its heel in an upright position on an iron-safe surface and plug into 120V ~ 60 Hz outlet. 5. Allow approximately 1 minute for the iron to reach the desired temperature. The ready light will turn off. 6. Hold the iron 7-15 inches away from the garment and press the burst of steam button once. 7. Wait a few seconds before pressing the burst of steam button again. The ready light will cycle on and then off during this process. Do not press the burst of steam button more than three times successively when ready light is ON. For best results, keep reservoir at least half full. 5 8. When finished, turn temperature dial to MIN, turn variable steam dial to O and unplug iron. Allow iron to cool before cleaning the exterior of the iron or storing. CAUTION: Avoid coming in contact with escaping steam. CLEANING STEAM VALVE 2. Dip the steam valve into white vinegar to dissolve calcium and mineral deposits. 1. Turn the variable steam dial counter-clockwise to the descaling position and pull out to remove from the iron. 3. Never use any sharp or rough objects to remove the deposits from the Steam Valve. 4. Rinse the steam valve with tap water. 5. Replace the variable steam dial in the descaling position and gently press down until in position. 6. Turn the variable steam dial to ‘O’ position. DO NOT pour any chemicals into the water reservoir as they can damage the iron. FILLING THE WATER RESERVOIR NOTE: FILL THE RESERVOIR WITH TAP WATER OR DISTILLED WATER. DO NOT USE CHEMICALLY DESCALED WATER OR ANY OTHER LIQUIDS. 1. Unplug and allow the iron to cool before filling. 2. Turn the variable steam dial to no steam setting. 3. Hold the iron upright but slightly tipped. 4. Open the water fill cover by placing fingernail under one tab and lift up. 5. Using the enclosed beaker or a measuring cup, slowly pour water into the water fill. Do not fill past the maximum line on the water reservoir. 6. Close the water fill cover. EMPTYING THE WATER RESERVOIR NOTE: The water tank should be emptied after each use. 1. When finished, turn temperature control dial to MIN, turn the variable steam dial to ‘O’ position and unplug the iron from the electrical outlet. 2. While the iron is still warm, hold the iron over a sink and allow the iron to drain by tipping the point of the iron down. 3. Gently shake the iron to loosen any water drops that may be trapped. The warmth of the iron should dry out any remaining water. 4. Press the burst of steam and spray buttons to release any water remaining. NOTE: If you empty the water reservoir after the iron has cooled, set the iron in an upright position on its heel, plug it in and set the temperature dial to maximum heat for 2 minutes. Then unplug the iron and let it cool before storing it. 6 SELF CLEANING/FLUSHING SELF CLEANING/FLUSHING 1. Fill the water reservoir half full, see FILLING THE WATER RESERVOIR. 2. Stand the iron on its heel in an upright position on an iron-safe surface and plug into a 120V ~ 60 Hz. outlet. 3. Turn the temperature dial clockwise to the maximum setting ••• . 4. The ready light will turn off when the iron has reached the desired setting. 5. Wait for one more cycle–the ready light will cycle on and back off again. 6. Turn the temperature dial counter-clockwise to MIN. 7. Remove the cord from the outlet by grasping the plug rather than pulling the cord. 8. Turn the steam control knob counter-clockwise to descaling position . The knob will raise slightly. 9. Steam and hot water will flow through the vents until the water reservoir is emptied. 10. Gently move the iron back and forth until the water reservoir is empty. 11. Turn the steam control knob to ‘O’ position. STORING THE IRON Remove the cord from the outlet by grasping the plug rather than pulling the cord. Empty the water reservoir after each use, see EMPTYING THE WATER RESERVOIR. Wrap the cord around the cooled iron as shown . Allow the iron to COOL COMPLETELY before putting away. To protect the soleplate, place the iron in an upright position on its heel. CLEANING AND CARE CAUTION: Unplug the iron from the electrical outlet and allow to cool before cleaning the exterior of the iron and storing. Never immerse the iron in water. NOTE: Do not put any chemical cleaning agents or solvents in the water reservoir. If starch or other residues cling to the soleplate, use hot iron cleaner according to directions. Hot iron cleaner is available at mass merchandise, discount or hardware stores. IMPORTANT: Any servicing that requires disassembly must be performed by an authorized service center. 7 SERVICE INFORMATION SERVICE INFORMATION This appliance mus...
Dieses Handbuch ist für folgende Modelle:Bügeleisen - 3342 (51.41 kb)