Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• Use iron only for its intended use. • The iron should be turned to MIN before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead grasp plug and pull to disconnect. • Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. • Always disconnect iron from electrical outlet when filling with water or emptying and when not in use. • Burns can occur from touching hot metal parts, hot water or steam. Use caution when turning the iron upside down as there may be hot water in the reservoir. • Do not leave iron unattended while hot or connected or while on an ironing board. • Position iron carefully on ironing board to avoid it being knocked over. SPECIAL INSTRUCTIONS • This is a high wattage appliance. To avoid a circuit overload, do not operate another appliance on the same circuit. If an extension cord is absolutely necessary, a 13 ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. • This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. 2 SAVE THESE INSTRUCTIONS FEATURES DIAGRAM 1 1. Water fill hole 2. Spray nozzle 3. Variable steam dial 4. Spray button 5. Burst of steam button 6. Auto shut-off light and reset button USING YOUR IRON Note: Before you use your iron for the first time, you should flush the sole- plate steam vents to ensure that no stain is transferred onto fabric fromresidue possibly left in the vents from the manufacturing process. To do this, see SELF-CLEANING/FLUSHING. For best results, check garment labels for the temperature and steam setting recommended by the fabric manufacturer, or consult the enclosed garment care tips pamphlet for additional information. To prevent damaging garments from too hot of an iron, it is best to first iron garments that require a low temperature. If you should need to switch from a high setting to a lower temperature, for example Cotton to Nylon, allow the iron about 5 minutes to reach the lower temperature. Tips: If you are unsure of a garment’s fabric content, start on a low setting and test the iron on an area of the garment that does not show, such as a seam. Gradually increase the heat setting until wrinkles remove without damaging the fabric. 7. See-through water reservoir 8. Pivot cord 9. Power on/ready light 10. Temperature control dial 11. Non-stick soleplate 3 TEMPERATURE AND STEAM GUIDE Fabric Temperature/Steam Delicates Nylon Acetate Silk Low Polyester Wool Medium Cotton Linen High To freshen up garments made of velvet, felt, suede or velour, hold the steaming iron horizontally 2 inches above the fabric for a gentle steaming. Make sure the iron does not come in contact with the fabric. To prevent shine, iron dark garments or those made of silk, acetate or rayon inside out. DIAGRAM 2 DIAGRAM 3 TEMPERATURE CONTROL DIAL VARIABLE STEAM DIAL USING AS A DRY IRON The iron can be used on the dry setting with or without water in the tank, however it is best to avoid having the tank too full of water while dry ironing. 1. Position temperature control dial to MIN, lowest setting. Diagram 2. 2. Turn the variable steam dial to NO STEAM. Diagram 3. 3. Stand the iron on its heel in an upright position on an iron-safe surface and plug it in. 4. Turn the temperature control dial to the desired setting. Diagram 2. 5. When the ready light turns off, the iron has reached the desired temperature. 4 6. 6. 7. When finished, turn temperature control dial to MIN, lowest setting, and unplug. Allow the iron to cool before cleaning the exterior orstoring. NOTE: During ironing, the ready light may turn on again which indicates that the iron is heating up to maintain the proper temperature. CAUTION: If the iron has been used for a long time and is hot, DO NOT fill it with water. USING AS A STEAM IRON When using as a steam iron, be sure the temperature setting on thetemperature control dial is within the STEAM range to avoid water spotting on a garment. 1. Position temperature control dial to MIN, lowest setting. Diagram 2. 2. Position the variable steam dial to lowest setting. Diagram 3. 3. With the unit UNPLUGGED, fill the iron with water. (See FILLING THEWATER TANK instructions.) 4. Stand the iron on its heel in an upright position on an iron-safe surfaceand plug in. DIAGRAM 4 DIAGRAM 5 5. Turn the temperature control dial to STEAM. Diagram 2. 6. Allow approximately 2 minutes for the iron to reach the desired temperature. (The ready light will turn off.) 7. Turn the variable steam dial counter clockwise to the desired amount of steam. Diagram 3. As soon as the iron is held horizontally, steam will flow thro...
Dieses Handbuch ist für folgende Modelle:Bügeleisen - 3314 (56.89 kb)