Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Braun Dateigröße: 116.19 kb Dateiname: Unterrichtssprache:

* If pressed too frequently, it can drip. Should this happen, wait a few seconds before using it again. Spray (coming from the nozzle 3 ): The spray function can be used at any temperature, to dampen laundry. To do so, press the button 7 (water spray = blue). Spray / shot of steam 2-function button: With the model 2010 the functions «water spray» and «shot of steam» can be activated with a 2-function button. The desired function can be selected by turning the button 7 as far as it will go. The marking (blue = water spray or red = shot of steam) must point to the respective function (f). Turn the button from blue (spray) to red (shot of steam) anti-clockwise and from red to blue clockwise (f). Storage After ironing, always pull the plug out of the wall outlet. Set the temperature selector 1 to «min.» (b) and the steam regulator 4 to « • » (= steam off) (c). To empty the iron hold it with the open water tank opening 2 downwards (h) and shake it 1 or 2 times. The pivoting cord 9 conveniently winds up around the cord storage k . IMPORTANT: Store the cool steam iron in a dry place and always standing on its heel rest j . The sole plate may be damaged by remaining water if it is stored horizontally. The warranty does not cover faults or damage resulting from improper storage of the iron. Maintenance and Cleaning All models have an aluminium sole plate. To prevent damaging it, do not iron over buttons or zippers, etc. Clean the sole plate regularly, particularly if you use starch or other ironing aids. To remove mineral/starch residues use a vinegar and water mixture in the ratio of 1:2. Never use abrasive scouring pads, powders or liquids. The steam vents m and jet of steam outlets p may be cleaned with a toothpick or cotton swabs and vinegar solution, if necessary. Decalcifying / Self- Braun Combi-jet irons (anti-calc. valve) to prevent you to clean residues from Do not use commercial decalcifiers; damage the sole plate. We recommend the self-cleaning function every 1. Turn the steam regulator 4 to the position « • » (= steam off). 2. Fill the water tank to the marking «max.» L and turn the temperature selector 1 to the lll marking («self-cleaning» = SC) (A). 3. Plug the iron into the socket and wait till the pilot light 8 goes off. 4. Unplug the iron and hold it over a sink. 5. Turn the steam regulator 4 clockwise to the end of the red marking (B) and then 6. keep turning in to the double-arrow marking . The steam regulator will lift (C) . 7. Pull out the steam regulator together with the valve vertically (D). Do not touch the lower end of the anti-calc. valve with your fingers, to avoid a possible greasy film. 8. Allow all water to drain through the steam vents in the sole plate, while shaking the iron slightly. (Caution: Hot water and steam come out from the sole plate.) 9. Wait for the sole clean it (see «Maintenance 10. Make sure that the sole before storing it. Cleaning the anti-calc. valve on regulator During the time the sole plate is cooling recommend to decalcify the anti-calc. valve the following way: 1. Put a small quantity of white vinegar (not vinegar essence) or lemon juice into a glass or bowl. 2. Immerse just the bottom part of the valve in the liquid, wait till it is decalcified and carefully brush of remaining residue (E). Do not use a metal brush. 3. Then, rinse it under running water without touching the lower end of the valve. Re-inserting the steam regulator with anti-calc. valve 1. Re-insert the steam regulator so that the double-arrow aligns with the marking on the iron (F). 2. Then push it down carefully and at the same time turn the button anti-clockwise. 3. Keep turning the button to the marking « • » (= steam off). 4. If your iron has the shot of steam, refill the tank with water, heat the iron up and press the button 7 3 to 4 times in the shot of steam function before ironing, to rinse the iron. ATTENTION: The iron must not be used without the steam regulator and the anti-calc. valve. Ironing Guide To begin ironing, it requiring a lower temperature , and continue with those temperature (e. g. cotton, . Silk and silk-like synthetics tend therefore before using the water test it on an inconspicuous spot first. Fabrics Temperature regulator setting Steam regulator setting Synhetics (acrylic, acetate) l • (= steam off) Silk, rayon, nylon, polyester, cotton blends ll • (= steam off) to max. Wool ll • (= steam off) to max. Cotton lll • (= steam off) to max. Linen lll to...

Herunterladen

Geben Sie zwei Ziffern: