Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
2. To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3. The iron should always be turned to Off . before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect. 4. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. 5. Always disconnect iron from electrical outlet when filling with water or emptying and when not in use. 6. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. 7. Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board. 8. Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir. 9. If the malfunction indicator goes on, the flatiron is not operating normally. Disconnect from the power supply and have the flatiron serviced by qualified service personnel. SPECIAL INSTRUCTIONS 1. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, a 10-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. SAVE THESE INSTRUCTIONS More specifically: DO NOT let children or untrained persons use the appliance without supervision. NEVER immerse the iron, cable or plug in any liquid. DO NOT leave the hot iron touching fabrics or very inflammable surfaces. DO NOT leave the appliance unnecessarily plugged in. Disconnect the plug from the mains when the appliance is not being used. NEVER touch the appliance with wet or damp hands. DO NOT use the power cord or the appliance in order to pull the plug out of the socket. DO NOT leave the appliance exposed to the weather (rain, sun, etc. ). DO NOT leave the iron without supervision when it is connected to the power supply. DO NOT fill the reservoir with water before removing the plug from the socket. PLEASE NOTE! Do not use chemical additive, scented substances or decalcifiers. Failure to comply with the above-mentioned regulations leads to the loss of guarantee. DESCRIPTION OF DEVICE (1). Spray organ (2). Filler door (3). Steam dial (4). Shot-steam button (5). Spray button (6). LCD window (7). Maximum filling level (8). Temperature button (9). Handle cover (10). Cord bushing (11). Supply cord (12). Rear Bushion (13). Rear top cap (14). Handle (15). Rear middle cap (16). Transparent water tank (17). Plate temperature control light (18). Self-cleaning button (19). Plastic skirt (20). Plate with steam vents GENERAL INSTRUCTIONS When using the iron for the first time, you may notice a slight emission of smoke and hear some sounds made by the expanding plastics. This is quite normal and it stops after a short time. We also recommend passing the iron over an ordinary cloth before using it for the first time. PREPARATIONS Soft the laundry to be ironed according to the international symbols on the garment label, or if this is missing, according to the type of fabric. Start ironing the garments requiring a low temperature. This reduces the waiting times (the iron takes less time to heat up than to cool down) and eliminates the risk of scorching the fabric. STEAM IRONING Filling the reservoir - Check that the plug is disconnected from the socket. - Move the steam selector (3) to “0” [Fig. 1]. - Open the lid (2). - Raise the tip of the iron to help the water enter the opening without overflowing. - Slowly pour the water into the reservoir using the special measure (20) and taking care not to go over the maximum level (about 300ml) indicated by “MAX” on the reservoir [Fig. 2]. - Close the lid (2). We recommend using the lowest temperatures with fabrics that have unusual finishes (sequins, embroidery, flush, etc.). If the fabric is mixed (e.g. 40% cotton 60% synthetics), set the thermostat to the temperature of the fibre requiring the lower temperature. If you don’t know the composition of the fabric, determine the suitable temperature by testing on a hidden corner of the garment. Start with a low temperature and increase it gradually until it reaches the ideal temperature. Never iron areas with traces of perspiration or other marks: the heat of the plate fixes the stains on the fabric, making them irremovable. The size is more effective if you use a dry iron at a moderate temperature: excess heat scorches it with the risk of forming a yellow mark. To avoid marking silk, woolen or synthetic garments shiny, iron them inside out. To avoid marking velvet garments shiny, iron in one di...