Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
24” on-center studs will require framing to proper opening size. 2. DETERMINE DISTANCE ABOVE THE FLOOR. Use the following chart to determine the recommended wall opening above the floor: Wall Opening Working Height Above the Floor AVD40/45 Series AVD50 Series 24” 30” 29”-30.”-32.” 28” 34” 33”-34.”-36.” 30” 36” 35”-36.”-38.” 32” 38” 37”-38.”-40.” 3. ATTACH CLEATS. Fasten 2x4 cleats to wall studs to provide a level surface on which to rest cabinet. 4. MOUNT CABINET. Lift cabinet into place and attach it to studs using the six supplied screws. Mounting holes positions are indicated by the arrows. On AVD45 and AVD50 Series models, remove the wireway cover to access mounting hole. Be sure to allow for wall covering thickness behind cabinet face frame. Plumb and shim cabinet to fit. 5. CONNECT WIRING (Fig. 2) (AVD45 & AVD50 Series only) Remove wireway cover. Bring house wiring into cabinet access hole and attach wiring to cabinet with an approved wire strain relief. Connect black to black, white to white and green/bare wire from house wiring to ground fixing terminal at the top end of the cabinet. Replace cover. CAUTION: DO NOT ALLOW WIRE TO EXTEND OUTSIDE OF WIRING BOX. EXPOSED WIRES CAN BECOME PINCHED AND ELECTRICAL SHOCK HAZARD MAY RESULT. Fig. 1 Fig. 2 OPERATING INSTRUCTION (Fig. 3) Control Panel (AVD45 and AVD50 Series) SAFETY SWITCH The Ironing Board depresses this switch when placed in its storage position. This disconnects all power to the ironing center controls. TIMER Work Lamp, Pilot Light and Receptacle are powered ONLY when timer is set. Set the amount of time you will be ironing by turning the knob clockwise. The timer can be manually turned to “0” (Off) at any time. Turn to “0” (Off) position when not in use. PILOT LIGHT When light is lit, it shows that the timer is set and that the power is “ON”. WORK LAMP The lamp will come on when the timer is set. A 40 watt max bulb is recommended. ELECTRICAL RECEPTACLE The Ironing Center is equipped with 3-prong grounded receptacle. CAUTION: Make sure your iron’s power cord does not interfere with operation of the SAFETY SWITCH when board is being placed in its storage position. Fig. 3 CABINET DOOR (Fig. 4) NOTE: Hinges, and hardware are supplied with all units. Doors are included with AVD40KN, AVD40WN, AVD45KN, and AVD45WN models. Decorative doors may be purchased separately for AVD40N, AVD45N and AVD50N models. Maximum weight of door must not exceed 25 lbs. (See Service Parts List) 1. MOUNTING THE CABINET DOOR Door may be hinged from either side of the cabinet. Both sides of the cabinet has pre-punched holes. Use two hinges (supplied) to fix door to the cabinet. Hinges should be placed on top and bottom section of the cabinet. Attach the hinge to cabinet and door using the screws supplied. Use the decorative plugs (supplied) to cover the remaining pre-punched holes. . Flat Head, #6 x 1/2” - Door to Hinge & Hinge to Cabinet . Pan Head, #6 x 3/8” - Magnetic Catch to Cabinet . Flat Head, #5 x 3/8” - Strike Plate to Door 2. INSTALLING MAGNETIC CATCH Magnetic catch is attached opposite the hinge. Attachment position is located on the top section of the cabinet and the door. Attach the magnetic catch 2A onto cabinet using the screws supplied. Attach the strike plate 2B onto door in line with magnetic catches using the screw (supplied). 3. LAMP REPLACEMENT Ensure the power is switched off (Timer is on “0” (Off) position). Insert small screwdriver or slim knife (as shown), ease catch to side and slip out diffuser. Replace lamp (40 watt max). Slide diffuser back into aperture and “click” into place. Fig. 4 PLASTIC SHIPPING LOCKS Fig. 5 MAINTENANCE IRONING CENTER BOARD IS FITTED WITH HEAT RESISTANT COVER. TO AVOID DAMAGE TO THE COVER DO NOT WASH THE COVER The laminated surface of the unit may be wiped clean with non-abrasive household cleaner. IRONING BOARD HEIGHT ADJUSTMENT (Fig. 5) MODEL AVD50N IMPORTANT: Remove the plastic shipping locks from each side of the board pivot. The Ironing Board has three working heights, to adjust the board: 1. Lower board to the first operating position(lowest position). 2. Hold the board with one hand (NOT BY THE NOSE) and support the pivot rod with the other hand. 3. Adjust the Ironing board to the desired position by lifting the board (NOT BY THE NOSE) and moving it to the path of height adjust bracket. NOTE: in order to store the Ironing board, it must be on its lowest position. MODELES UNITE DE REPASSAGE INTEGRE LISEZ ET CONSERVEZ CES INSTRUCTIONS ATTENTION Uniquement pour le serie AVD45 et AVD50) Toute l’installation electrique devra etre faite en conformite avec les reglementations locales et/ou nationales en vigueur. Pour raison de securite, ce produit devra etre isole par un fil de terre. Si vous n’etes pas familier avec les methodes d’installation electrique, prevoyez l’utilisation d’un electricien qualifie. L’unite de repassage doit etre installe sur A SEPARE 15 amperes circuit d’eviter que le circuit ne soit surcharge. Coup...