Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
6. Set variable steam control to " 0". 7. Allow iron to cool in an upright position before storing. WARNING! Use caution when emptying the iron. Burns may occur from touching hot metal surfaces, hot water or steam. STORAGE1. Always turn the variable steam control to “0” after you have emptied the water tank. 2. Allow the iron to cool down. 3. Always store the iron in the upright position to protect the soleplate. 4. From time to time, clean the exterior of the iron with a damp cloth and wipe dry. 5. If you use spray starch, wipe the soleplate occasionally with a soft damp cloth to prevent the build-up of deposits. 6. If the iron has not been used for a few weeks, hold the iron horizontally and allow to steam for 2 minutes before ironing. SELF-CLEANINGIn order to remove calcium and built-up particles, the self-cleaning system should be run at least once a month. • Fill the water beaker provided halfwayand then pour into the water reservoir. • Set the variable steam control to the no steam position. • Insert the main plug into the wall socket. • Set the temperature control dial to the maximum temperature. • Wait until the thermostat light goes off and steam iron has reached preset temperature. • Remove the plug from the wall socket. • Hold the steam iron horizontally over a sink. • Turn the variable steam control to “Self-Clean ” position. Hot water and steam will be emitted from the soleplate. Swing the steam iron lightly back and forth gently to allow lime and dust particles to come out. • When the water reservoir is empty, shift the variable steam control from “Self- Clean” position to “0”. • Stand the iron upright and insert the plug into the wall socket to let the iron heat up again. • Move the iron over a clean cotton cloth to clean the soleplate and let the remaining water on the soleplate evaporate. 3. Plug the cord into a polarized, 120V AC electrical outlet. 4. Turn the temperature dial to any of the temperatures within the steam band and allow the iron to heat for approximately 2 minutes before ironing. Place iron on its heel (on a stable, protected surface) while the iron is warming to the desired temperature. 5. Turn the variable steam control to the right to increase the amount of steam. (See figure 3) When using extra steam, the iron uses more water and it may be necessary to fill the tank more often. For refilling the iron with water follow the steps listed above. OPERATING INSTRUCTIONS 1. Turn temperature dial to "• • " or “MAX“ and turn the variable steam control to “0”. 2. Holding the iron at a slight angle, pour water slowly into the water filling inlet. See figure 2. Fill tank to desired level or to the “MAX” water level marking using the water filling flask. (When the iron is upright, see-through water tank allows you to gauge the amount of water.) DO NOToverfill the tank. 5 BLAST OF STEAM WARNING! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur. 6. Steam is produced as soon as the iron is held in the horizontal position. Steam will stop coming out when the iron is put on its heel in a vertical position or by turning the steam control dial to " 0". The blast-of-steam button is useful when ironing denim, cotton, and linens. It provides extra, sudden blasts of steam which aid in removing stubborn wrinkles. The blast-of-steam feature can be used with Dry or Steam ironing as desired. 1. Make sure the water tank is at least 1/2 filled with water. 2. Set the temperature dial. Place the iron on its heel (on a stable, protected surface) and allow it to heat for approximately 2 minutes. 3. With the iron in a horizontal position, press the blast of steam button several times to prime the pump. See Figure 4. NOTE: If the tank runs dry, remove the plug from wall outlet. Then, fill the iron with water and re-prime the pump. The iron may be filled with water while it is hot. 4. For vertical steam, press the blast of steam button while holding the iron in a vertical position. See figure 5. The vertical steam function is useful for steaming curtains and drapes while still hanging. WATER SPRAY OPERATING INSTRUCTIONS 6 SELECTING IRON TEMPERATURES Always read garment labels and follow the manufacturer's ironing instructions. Refer to the "Ironing Chart" on page 9 for temperature recommendations: See figure 7. • Use low settings for synthetics. •• Use moderate settings for wool, silks, and blends. ••• Use high settings for cottons and linens. Fig. 7 NOTE: Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam. AUTOMATIC SHUT- OFF Fig. 4 Fig. 3For Steam Ironing Fig. 2 The water spray is useful on fabrics with stubborn wrinkles. Press the spray button and a jet of water will spray onto the fabric being ironed. See Figure 6. The water spray can be used with dry or steam ironing as desired. Fig. 6Fig. 5The auto shut-off safety function of your iron is designed to engage ...